background image

20

WARRANTY

THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES 

TO MODEL NUMBERS REQUIRED TO MEET THE CARB REQUIREMENTS.

TECHTRONIC INDUSTRIES NORTH AMERICA, INC., LIMITED WARRANTY  

FEDERAL AND CALIFORNIA EMISSION CONTROL SYSTEMS NON-ROAD AND SMALL 

OFF-ROAD ENGINES

The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Techtronic Industries North America, Inc., 

are pleased to explain the Emission Control System Warranty on your non-road or small off-road engine. In California, new small off-road 

engines must be designed, built, and equipped to meet the state’s stringent anti-smog standards. In other states, new 2000 and later model 

year non-road engines must be designed, built, and equipped at the time of sale to meet the U.S. EPA regulations for small non-road engines. 

The non-road engine must be free from defects in materials and workmanship which cause it to fail to conform with U.S. EPA standards for 

the first two years of engine use from the date of sale to the ultimate purchaser. Techtronic Industries North America, Inc., must warrant the 

emission control system on your non-road or small off-road engine for the period of time listed above provided there has been no abuse, 

neglect, or improper maintenance of your non-road or small off-road engine.
Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, and the catalytic con-

verter. Also included may be hoses, belts and connectors, and other emission-related assemblies.
Where a warrantable condition exists, Techtronic Industries North America, Inc., will repair your non-road or small off-road engine at no 

cost to you, including diagnosis (if the diagnostic work is performed at an authorized service center for RYOBI

®

 brand outdoor products), 

parts, and labor.

MANUFACTURER’S WARRANTY COVERAGE:

The 1995 and later small off-road engines are warranted for two years in California. In other states, 1997 and later model year non-road 

engines are also warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or replaced by 

Techtronic Industries North America, Inc., free of charge.

OWNER’S WARRANTY RESPONSIBILITIES

(a)  As the non-road or small off-road engine owner, you are responsible for the performance of required maintenance listed in your operator’s 

manual. Techtronic Industries North America, Inc., recommends that you retain all receipts covering maintenance on your non-road or 

small off-road engine, but Techtronic Industries North America, Inc., cannot deny warranty solely for the lack of receipts or for your 

failure to ensure the performance of all scheduled maintenance. Any replacement part or service that is equivalent in performance and 

durability may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of the engine manufacturer.

(b)  As the non-road or small off-road engine owner, you should be aware, however, that Techtronic Industries North America, Inc., may deny you  

warranty coverage if your non-road or small off-road engine or a part has failed due to abuse, neglect, improper maintenance, or unap-

proved modifications.

(c)  You are responsible for presenting your non-road or small off-road engine to an authorized service dealer as soon as a problem exists. 

The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact a Techtronic Industries North America, 

Inc., Customer Representative at 1-800-860-4050.

COVERAGE:

Techtronic Industries North America, Inc., warrants to the ultimate purchaser and each subsequent purchaser that your non-road or small 

off-road engine will be designed, built, and equipped at the time of sale, to meet all applicable regulations. Techtronic Industries North 

America, Inc., also warrants to the initial purchaser and each subsequent purchaser that your non-road or small off-road engine is free from 

defects in materials and workmanship which cause the engine to fail to conform with applicable regulations for a period of two years. The 

1995 and later small off-road engines are warranted for two years in California. In all other states for 1997 and later model years, EPA requires  

manufacturers to warrant non-road engines for two years. These warranty periods will begin on the date the non-road or small off-road 

engine is purchased by the initial purchaser. If any emission-related part on your engine is defective, the part will be replaced by Techtronic 

Industries North America, Inc., at no cost to the owner.
Techtronic  Industries  North  America,  Inc.,  shall  remedy  warranty  defects  at  any  authorized  RYOBI  engine  dealer  or  warranty  sta-

tion.  Any  authorized  work  done  at  an  authorized  dealer  or  warranty  station  shall  be  free  of  charge  to  the  owner  if  such  work  deter-

mines  that  a  warranted  part  is  defective.  Any  manufacturer-approved  or  equivalent  replacement  part  may  be  used  for  any  warranty   

maintenance or repairs on emission-related parts, and must be provided free of charge to the owner if the part is still under warranty.  Tech-

tronics North America, Inc., is liable for damages to other engine components caused by the failure of a warranted part still under warranty.
The California Air Resources Board’s Emission Warranty Parts List specifically defines the emission-related warranted parts. (EPA’s regula-

tions do not include a parts list, but EPA considers emission-related warranted parts to include all the parts listed below.)
These warranted parts are:  Carburetor, Spark Plug, Ignition, Air Filter, and Fuel Filter.

MAINTENANCE REQUIREMENTS

The owner is responsible for the performance of the required maintenance as defined by Techtronic Industries North America, Inc., in the 

operator’s manual.

LIMITATIONS

The Emission Control Systems Warranty shall not cover any of the following:
(a)  repair or replacement required because of misuse or neglect, lack of required maintenance, repairs improperly performed, or replace-

ments not conforming to Techtronic Industries North America, Inc., specifications that adversely affect performance and/or durability, 

and alterations or modifications not recommended or approved in writing by Techtronic Industries North America, Inc., and

(b)   replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled replace-

ment point.

The Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which the 

engine has been shown to meet Federal emission requirements.  Category C=50 hours, B=125 hours, and A=300 hours.

Summary of Contents for RY60511B























Reviews: