background image

17

MAINTENANCE

CUTTING CORNER

SIDE PLATE

DEPTH GAUGE

TOE

GULLET

HEEL

RIVET HOLE

TOP PLATE

PARTS Of A CUTTER

Fig. 4

HOW TO SHARPEN THE CUTTERS

See Figures 24 - 27.

Be careful to file all cutters to the specified angles and to 
the same length, as fast cutting can be obtained only when 
all cutters are uniform.

 

Using light but firm pressure, stroke towards the front 
corner of the tooth. Lift file away from the steel on each 
return stroke.

 

Put a few firm strokes on every tooth. File all left hand 
cutters in one direction. Then move to the other side and 
file the right hand cutters in the opposite direction.  Oc-
casionally remove filings from the file with a wire brush.

Fig. 5

Fig. 6

 

Tighten the chain tension enough that the chain does not 
wobble. Do all of your filing at the mid-point of the bar.  
Wear gloves for protection.

 

Use a 5/3 in. diameter round file and holder.

 

Keep the file level with the top plate of the tooth. Do not 
let the file dip or rock.

LEfT HAND 

CUTTERS

RIGHT HAND 

CUTTERS

Fig. 7

CAUTION:

Dull or improperly sharpened chain can cause excessive 
engine speed during cutting which may result in severe 
engine damage.

WARNINg: 

Improper  chain  sharpening  increases  the  potential  of 
kickback. Failure to replace or repair damaged chain can 
cause serious injury.

CLEANINg  THE  EXHAUST  PORT  AND 
MUFFLER

Depending on the type of fuel used, the type and amount 
of  lubricant  used,  and/or  your  operating  conditions,  the 
exhaust port and muffler may become blocked with carbon 
deposits. If you notice a power loss with your gas powered 
tool, a qualified service technician will need to remove these 
deposits to restore performance.

SPARK ARRESTOR

The spark arrestor must be replaced every 50 hours or yearly 
to ensure proper performance of the product. Spark arres-
tors may be in different locations depending on the model 
purchased. Please contact the nearest service dealer for the 
location of the spark arrestor for your model.

Summary of Contents for RY52504

























Reviews: