background image

18

MAINTENANCE

CLEANINg AIR FILTER SCREEN

See Figure 28-29.

For proper performance and long life, keep air filter clean.

  Remove the air filter cover by pushing down on the latch 

with your thumb while gently pulling on the cover.

  Brush the air filter screen lightly to clean. 

  Replace the air filter cover by inserting the tabs on the 

bottom of the cover into the slots on the air filter base; 
push the cover up until it latches securely in place.

NOTE: For best performance, replace annually.

FUEL CAP

WARNINg:  

A leaking fuel cap is a fire hazard and must be replaced 
immediately.

The fuel cap contains a non-serviceable filter and a check 
valve. A clogged fuel filter will cause poor engine performance. 
If  performance  improves  when  the  fuel  cap  is  loosened, 
check valve may be faulty or filter clogged.  Replace fuel 
cap if required.

SPARK PLUg REPLACEMENT

This engine uses a Champion RCJ6Y with .05 in. electrode 
gap. Use an exact replacement and replace annually.

STORINg THE PRODUCT

See Figure 30.

  Clean all foreign material from the product. Store idle unit 

indoors in a dry, well-ventilated area that is inaccessible 
to children. Keep away from corrosive agents such as 
garden chemicals and de-icing salts.

  Abide by all ISO and local regulations for the safe storage 

and handling of gasoline. 

  Always place the scabbard on the saw bar when trans-

porting or storing the pruner. The scabbard is a snug fit 
and  must  be  attached  very  carefully  due  to  the  sharp 
teeth on the saw chain. This is best done by grasping the 
scabbard at one end, in the center portion of the scab-
bard, and carefully sliding it over the chain as shown. Use 
caution to avoid the sharp teeth of the chain.

  NOTE:  The saw chain is very sharp. Always wear protec-

tive gloves when handling the chain.

 

 To use the hanger cap, push in the button and place the 

hanger cap over end of the lower end attachment shaft. 
Slightly rotate the cap from side to side until the button 
locks into place.

When storing 1 month or longer:

  Drain  all  fuel  from  tank  into  a  container  approved  for 

gasoline. Run engine until it stops.

Fig. 8

AIR fILTER

COVER

fILTER SCREEN

  Fig. 9

AIR fILTER 

COVER

LATCH

PULL COVER 

TO OPEN

LATCH

  Fig. 30

Summary of Contents for RY52504

























Reviews: