10
DISPOSAL INFORMATION
The appliance contains electric and electronic
components and may not be disposed of as household
garbage.
The local and currently applicable legislation must be
observed unconditionally.
SPECIFIED CONDITIONS OF USE
The appliance is suitable for picking up dry, non-
fl ammable dust and liquids.
This appliance is designed solely for use in the private
sector and for the designated purpose. The appliance is
not suitable for commercial use. Don’t use the appliance
outdoors (unless it has been specifi cally designed for
use outdoors). Don’t subject the appliance to heat,
direct sunshine or very high moisture (e.g., rain).
Any other use is considered as improper use. The
manufacturer accepts no liability for any damage
resulting from such use. The risk for such use is borne
solely by the user.
Proper use also includes proper operation, servicing
and repairs as specifi ed by the manufacturer.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the
product described under “Technical Data” fulfi lls all the
relevant provisions of the directives 2011/65/EU (RoHs),
2014/35/EU, 2006/42/EC and the following harmonized
standards have been used:
EN 60335-1:2012 + A11:2014
EN 60335-2-2:2010+A11:2012+A1:2013
EN 62233:2008
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 50581:2012
Winnenden, 2016-04-21
Branko Lenger
Senior Vice President, Engineering and Quality - Asia,
Engineering Commercial Product Development
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
PACKAGING CONTENT
See Fig. 2 - Fig. 4
Carefully unpack the contents of the box.
Hold the two clamps, which hold the upper section in its
position and fold them upwards.
Loosen the clamps, remove the upper section, and
remove the contents from the tank.
Please check the parts using the components list to
make sure they are complete and that there has been
no damage in transport.
If any parts are missing or damaged, then please
contact your dealer immediately.
ASSEMBLY
1. Ensure that the power cord is disconnected from the
power outlet.
2. Undo the clamps (Fig. 2).
3. Lift the top section off the tank (Fig. 3).
4. Remove the contents from inside the tank (Fig. 4).
5. Turn the tank upside down, and insert the casters on
to the four feet of the tank.
6. Ensure that they are mounted correctly. Do not over
tighten (Fig. 5).
7. Insert the handle into the slots on the power head,
pressure into place and secure it by tightening
screws (Fig. 6).
8. For dry vacuuming, install the supplied dust fi lter
and dust bag (Fig. 7, Fig. 8).
9. For wet vacuum cleaning, install the supplied foam
fi lter (Fig. 9)
10. Replace the top section on the tank (Fig. 10).
11. Align the top section with the clamps and snap into
place by applying pressure until clamps click
(Fig. 10).
12. Insert the large end of the hose into the front inlet of
the tank and turn to lock (Fig. 11).
13. Fit the required accessory on to the suction tube
(Fig. 12).
OPERATION
DRY VACUUMING
WARNING
Ensure that you read, understand, and apply the
safety instructions.
Reminder: DO NOT vacuum hazardous substances.
The use of an incorrect dust bag will invalidate the
warranty.
1. Ensure that the power cord is disconnected from the
power outlet.
2. Ensure that the tank is clean and free of dust and
dirt.
RVC-1218P-G - Version01.indd 10
RVC-1218P-G - Version01.indd 10
21.05.2016 19:19:39
21.05.2016 19:19:39
