background image

ASSEMBLY

13

Fig. 9

See Figure 9

12. Position the fence at the rear of the tabletop so that

the 2 square nuts 

(AR)

are positioned in the 2 slots in

the table. Slide the fence forward (always parallel with
the front of the table). When the fence is in the desired
location, tighten the knob screws 

(L)

by turning 

clockwise.

L

L

ASSEMBLE 2 FEATHERBOARDS 

FOR THE FENCE

See Figure 10

13. Insert the hex head screw 

(AF)

into the sliding block

(R)

. Place the sliding block into the slot of the feather-

board

(Q)

. Secure by placing washer 

(AK)

over the

hex head screw 

(AF).

Screw together by turning the

knob

(M)

clockwise.

NOTE:

Do not completely tighten

at this stage.

Fig. 10

Fig. 11

See Figure 11

14. Position the featherboards on the fence and secure

by turning the knobs 

(M)

clockwise.

M

M

ASSEMBLE THIRD FEATHERBOARD 

ON TABLETOP

See Figure 12

15. Insert the hex head screw 

(AF)

through the hex head

hole in tabletop. Position the featherboard 

(Q)

over the

bolt. Screw together by placing washer 

(AK)

over the

bolt and turning the knob 

(M)

clockwise.

NOTE:

This

assembly must be securely tightened in the key hole
slot in the tabletop.

AF (2)

AK (2)

Q

AK

M

R

AF

Fig. 12

AF (1)

AK (1)

Q

AF

M

AK

Summary of Contents for RT601W





























Reviews: