inspected by qualified service staff. Each time the
pump is put into operation, please make sure that
the pump is set up securely and firmly standing.
■
To put the unit into operation, please plug the mains
plugs into a socket. If the water level has reached
or exceeded the cut-in level, the pump will start to
4
run immediately. To stop the operation of the pump,
please pull the mains plug off the socket.
■
The electrical RYOBI pumps are equipped with
an integrated thermal motor protection feature.
In the case of overload, the motor will switch off
independently and on again after cooling down. For
possible causes and their elimination, please refer
to the “Maintenance and troubleshooting” section.
Please note that the pump can only be operated
with liquids > 50°C for a short period of time (see
Technical data).
■
Your pump is equipped with a purge which is used
to evacuate the air. Ensure that this purge is clean.
WARNING
WARNING
Prior to carrying out any maintenance work, the
pump must be separated from the electrical mains.
If you fail to separate the unit from mains, there is a
risk of an inadvertent start of the pump.
We decline any liability for damage caused by
inappropriate repair attempts. Any damage caused
by inappropriate repair attempts will avoid all
warranty claims.
■
Observing the conditions of use and the ranges of
application of the present device will reduce the risk
of possible operational malfunction and contribute
to extend the lifetime of your unit. Sand and other
abrasive matters contained in the liquid discharged
will speed up the process of wearing and tearing
and accelerate the drop in performance.
■
If the unit is operated properly, it will not require any
maintenance. Where applicable, you may clean the
hydraulic part from sediments and dirt. This can be
done by counter-flushing the unit with clear water
using a hose to be connected through the pressure
port of the pump. To remove tenacious dirt, the foot
of the pump (2) can be removed by loosening the
screws located at the bottom of the pump. To avoid
any hazard, any further disassembly as well as
the replacement of parts must only be done by the
manufacturer or a by an authorised service provider.
■
Water left in the pump may freeze in case of frost
and thus cause considerable damage. Therefore,
the pump must be removed from the liquid being
discharged and fully drained when temperatures are
below the freezing point of the liquid. Please store
the pump in a dry, frost-protected place.
■
In the case of malfuntion, you should first of all
check whether it it was caused by an operating error
or some other reason which cannot be attributed to
a defect of the device - for instance a power failure.
■
The list below shows some possible malfunctions
of the device, possible causes and tips on their
elimination. All the measures referred to may only
be carried out with the pump being separated from
the electrical mains. If you yourself feel eliminate
any of these malfunctions, please contact unable
to the customer service department or your point of
sales. Any repair beyond the scope specified below
must only be performed be qualified staff. Please
bear in mind that all warranty claims will become
void in the case of damage caused by inappropriate
repair attempts, and that we decline any liability for
any ensuing damage.
■
Nobody must be in the water while the pump is
running. The pump must only be operated in the
performance range indicated on the type plate.
■
Dry-running - i.e. operating the pump without
discharging water is to be avoided since the
absence of water may cause the pump to run
hot. This may cause considerable damage on the
device.
■
Please make sure that the electrical plug
connections are in flood-proof area.
■
As long as the device is connected to the electrical
mains, one must never reach with one’s hands into
the opening of the pump.
■
Please inspect the pump visually prior to each use.
■
This applies in particular to the mains connection
line and the mains plug. Make sure that all screws
are firmly tightened, and verify the perfect condition
of all connection. A damaged pump must not be
used. In any case of damage, the pump has to be
inspected by qualified service staff. Each time the
pump is put into operation, please make sure that
the pump is set up securely and firmly standing.
■
To put the unit into operation, please plug the mains
plugs into a socket. If the water level has reached
or exceeded the cut-in level, the pump will start to
run immediately. To stop the operation of the pump,
please pull the mains plug off the socket.
■
Your pump is equipped with a purge which is used
to evacuate the air. Ensure that this purge is clean.
MAINTENANCE AND TROUBLE SHOOTING
