background image

1

Safety, performance, and dependability have been given 
top priority in the design of your petrol pole hedge trimmer.

INTENDED USE

The petrol pole hedge trimmer is intended to be used only 
by adults who have read and understood the instructions 
and warnings in this manual and can be considered 
responsible for their actions.
The product is only intended for use outdoors in a well-
ventilated area. For safety reasons, the product must be 
adequately controlled by using two-handed operation.
The product is designed for home or domestic use. It is 
intended to cut and trim hedges, shrubs, and similar 
vegetation where stems or twigs are less than 28 mm thick. 
It should be used in dry, well-illuminated conditions. 
It is not intended to cut grass, trees, or branches. It should 
not be used for any other purpose than hedge trimming.

 

 WARNING

To avoid serious personal injury, do not attempt to use 
the product until you read thoroughly and understand 
completely these instructions. Save these instructions 
and review frequently for continuing safe operation and 
instructing others who may use the product.

Save these instructions.

GENERAL SAFETY WARNINGS

 

 WARNING

Read all safety warnings and all instructions.

 Failure 

to follow the warnings and instructions may result 
in electric shock, fire, and/or serious injury. Save all 
warnings and instruction for future reference.

PREPARATION

 

 WARNING

The pole hedge trimmer can cause serious injuries. 
Read the instructions carefully for the correct handling, 
preparation, maintenance, starting, and stopping of the 
pole hedge trimmer. Become familiar with all the controls 
and the proper use of the pole hedge trimmer.

 

Ŷ

Do not allow children or untrained individuals to use the 
product.

 

Ŷ

Beware of overhead power lines.

 

Ŷ

Keep all bystanders, children, and pets at least 15 
m away. Avoid operating while people, especially 
children, are nearby.

 

Ŷ

Dress properly. Do not wear loose clothing or jewellery, 
which can become entangled in moving parts.

 

 WARNING

The operation of any power tool can result in foreign 
objects being thrown into your eyes, which can result in 
severe eye injury. Before operating the product, always 
wear safety goggles or safety glasses with side shields 
and, when needed, a full face shield. Ryobi recommends 
wide vision safety mask for use over eyeglasses or 
standard safety glasses with side shields.

 

Ŷ

Do not operate the equipment when barefoot or when 
wearing sandals or similar lightweight footwear. Wear 
non-skid, protective footwear that will protect your feet 
and improve your footing on slippery surfaces.

 

 WARNING

Exercise extreme caution when handling fuel. Petrol is 
flammable and the vapours are toxic and explosive.

 

Ŷ

Use only fuel containers which are approved for petrol.

 

Ŷ

Add fuel before starting the engine. Never remove 
the cap of the fuel tank or add fuel while the engine is 
running or when the engine is hot.

 

Ŷ

Do not smoke.

 

Ŷ

Always refuel outdoors. Never refuel indoors or in a 
poorly ventilated area. Keep away from all sources of 
ignition, sparks, and flames.

 

Ŷ

Never store the product with fuel in the fuel tank inside a 
building where ignition sources are present, such as hot 
water and space heaters, clothes dryers, and the like.

 

Ŷ

Wipe spilled fuel from the product. Move 9 m away from 
refuelling site before starting engine.

 

Ŷ

Replace all fuel tank and container caps securely.

 

Ŷ

If the fuel tank has to be drained, do this outdoors.

 

Ŷ

If the cutting mechanism strikes any foreign object or 
the pole hedge trimmer starts making any unusual 
noise or vibration, shut off the power source and allow 
the pole hedge trimmer to stop. Disconnect the spark 
plug wire from the spark plug and take the following 
steps:

 

Ɣ

inspect for damage

 

Ɣ

check for, and replace, any loose parts.

 

Ŷ

Damaged parts should be replaced or repaired 
immediately with parts having equivalent specifications.

 

 WARNING

The product is extremely noisy in operation. You must 
wear ear protection to reduce the risk of long term 
hearing injury.

 

 WARNING

Always wear safety goggles or safety glasses with 
side shields when operating the product. Failure to do 
so could result in objects being thrown into your eyes 
resulting in possible serious injury.

 

Ŷ

To stop the pole hedge trimmer in an emergency, press 

Summary of Contents for RPHT254O





































Reviews: