ENGLISH
7
ASSEMBLY
ASSEMBLY
OPERATION
n
Place the knob nut (item 15) onto the bolt and tighten
the knob nut securely.
ATTACHING THE SAFETY GUARD
(FIG.4)
Follow these steps to attach the safety guard.
n
Place the safety guard (item 11) around the lower shaft
and align with the bracket (item 19).
n
Install the screws (item 18) through the holes and tighten
the safety guard.
EXTENSION CORD RETAINER
(FIG.5)
An extension cord retainer (item 4) is located on the bottom
of the trimmer. This provides strain relief for the cord,
preventing unwanted disconnects.
n
Use the extension cord retainer when you connect the
extension cord to the power cord to prevent disconnection.
Use only an outdoor approved extension cord.
n
Loop the extension cord through the extension cord
retainer slot located on the bottom end of the trimmer.
n
Pull loop of extension cord around tongue and pull tight.
n
Attach extension cord to plug on trimmer.
SHOULDER STRAP
(FIG.6)
A shoulder strap(item 10) is supplied for your greater comfort.
n
Simply attach the clip(item 20) of the shoulder strap onto
the loop (item 21) at the front of the motor housing (item 5).
INTENDED USE
This grass trimmer is designed for cutting grass and similar
soft vegetation in private and hobby garden areas which
are not accessible with a lawn mower.
The device is not allowed to be used in public gardens,
parks, sports centers or at roadsides as well as in agriculture
and forestry.
This line trimmer is not allowed to be used for cutting or
chopping hedges, shrubs, bushes or flowers.
WARNING:
The product may throw objects during operation,
causing injury to the operator or to bystanders. Always
wear suitable eye protection, boots, gloves and long,
heavy trousers while operating the product.
STARTING AND STOPPING THE TRIMMER
(FIG.7)
n
To start the trimmer: press the lock button (item 3) and
then press the trigger (item 2). Release the lock button
once the motor has started.
n
To stop the trimmer: Release the trigger.
OPERATING THE TRIMMER
(FIG.8)
Follow these steps to operate the trimmer.
n
Plug the trimmer cord into an extension cord approved
for outdoor use. Refer to “Electrical Safety Rules” earlier
in this manual.
n
Once the unit is connected to electric power, the LiveTool
Indicator (item 7) will show a blue light.
n
Put the shoulder strap (item 10) over your shoulder
opposite side to the unit. Adjust shoulder strap to the
most comfortable length.
n
Hold the trimmer with your right hand on the trigger handle
and your left hand on the front handle.
NOTE:
Keep a firm grip with both hands during operation.
n
Place the trimmer on the side of your body with the motor
behind and away from your body.
n
Press the lock button and then the trigger to start the
trimmer.
n
The trimmer will build up speed steadily.
n
Trim grass and weeds in a right-to-left motion with the
line parallel to the ground.
NOTE:
If the machine is overloaded, thermal protection inside the
unit will cut off the trimmer. Leave the trimmer for about
10 minutes before turning it ON again. The line trimmer
should then start.
n
To switch off the line trimmer, simply release the trigger.
WARNING:
After switching off, the nylon line will continue to rotate
for a few more seconds. Maintain vigilance until the
line completely stops.
CUTTING TIPS
n
Inspect and clear the area to be trimmed for any rocks,
broken glass or wire that could be thrown or become
entangled in the cutting line. Trim only when grass or
weeds are dry . Keep the cutting line parallel to the ground.
n
Cut grass or weeds over 20cm tall from the top to the
bottom in small amounts. This will prevent grass becoming
wrapped around the trimmer head assembly, which may
result in damage due to overheating. If grass becomes
wrapped around the trimmer head assembly, stop the
trimmer, unplug it and remove the grass.
n
Move the trimmer slowly in and out of the area you are
cutting, keeping the trimmer at the desired cutting height.
n
Use the tip of the line to do the cutting. Do not force the
trimmer head assembly into uncut grass.
n
Feed out some line as required during use to prevent the
line from retracting into the cutting head.
