background image

11

TROUBLESHOOTING

If these solutions do not solve the problem, contact your authorised service dealer.

PROBLEM

POSSIBLE CAUSE

SOLUTION

Engine will not start.

No fuel.

Push primer bulb until bulb is full of fuel. 

If bulb does not fill, primary fuel delivery 

system is blocked. Contact a servicing 

dealer. If primer bulb fills, engine may be 

flooded, proceed to next item.

Engine is flooded.

Pull starter with choke lever at “Run” 

position and wide open throttle. If engine 

does not start, move choke lever to 

“Full” position and repeat normal starting 

procedure. If engine still fails to start, 

repeat procedure with a new spark plug.

No spark.

Check spark. Remove spark plug. 

Reattach the spark plug cap and lay 

spark plug on metal cylinder. Pull the 

starter rope and watch for spark at spark 

plug tip. If there is no spark, repeat test 

with a new spark plug.

Starter rope pulls harder now than when 

new.

Contact a servicing dealer.

Engine starts but will not accelerate.

Engine requires approximately three 

minutes to warm up.

Allow engine to completely warm up. If 

engine does not accelerate after three 

minutes, contact a servicing dealer.

Engine starts but will only run at high 

speed at half choke.

Carburetor requires adjustment.

Contact a servicing dealer.

Engine does not reach full speed and 

emits excessive smoke.

Check lubricant fuel mixture.

Use fresh fuel and the correct 2-stroke 

lubricant mix.

Air filter is dirty.

Clean air filter. Refer to Cleaning the Air 

Filter earlier in this manual.

Spark arrestor screen is dirty.

Contact a servicing dealer.

Engine starts, runs, and accelerates but 

will not idle.

Idle speed screw on carburetor requires 

adjustment

Contact a servicing dealer.

NOTE:

 If your unit exhibits specific performance problem(s) where the Troubleshooting section recommends a clockwise screw 

adjustment on the carburetor and no adjustments have been made since original purchase, the unit should be taken to an 

authorized service centre for repair. In most cases, the needed adjustment is a simple task for the trained service representative.

Summary of Contents for RHT2660RN














Reviews: