17
GB
1.
A LOOK AT YOUR SAW (Fig. 1)
1. Upper door
2. Sawblade tension adjustment knob
3. Top band saw wheel
4. Cut height positioning knob
5. Cut height slide
6. Sawblade
7. Table
8. Drive wheel
9. Parallel guide
10.Lower door
11.On/Off switch with emergency stop system
12.Upper wheel tilt knob
13.Motor
14.Base
15.Sawdust extraction outlet
16.Transmission belt tension adjustment
17.Chip guard
18.Push stick
2.
PROPER USE OF YOUR SAW
This machine is designed to cut wood or plastic.
Only cut circles with a proper clamping device through the longitudinal axis of the workpiece because of the risk of twisting
of the workpiece by the sawblade.
When you cut boards on edge, use an appropriate set square for safer guiding.
Any other use of this saw is improper. The manufacturer shall under no circumstance be liable for damages resulting for
improper use of this saw.
If you modify your saw or use parts that have not been checked and approved by the manufacturer, unpredictable damage
may occur when the machine is operating.
2.1
SAFETY PRECAUTIONS
•
This machine is an electric tool which can cause severe burns in the event of negligence.
•
This is why you must read and comply with:
- this instruction manual, paying particular attention to the safety precautions set forth in each section,
- and, where applicable, the legal provisions relative to the handling of band saws.
•
Keep all documents provided with this machine in a safe place.
•
This machine must only be set up and used by people who are already familiar with band saws and who are constantly
conscious of the risks involved in the handling of such tools.
•
Minors must only use this machine within the framework of occupational training under the supervision of a specialist.
•
The non-appraisable risks referred to above are inherent to band saws and cannot entirely be eliminated by the safety device.
Risks linked to technical modifications made to the machine or the use of parts that were not checked and
approved by the manufacturer
•
Assemble the machine by scrupulously following the instructions in this manual.
•
Only use parts that have been approved by the manufacturer.
•
Do not alter the parts in any way.
•
Never use the machine when the doors of the sawblade protection mechanism are open.
•
Make sure that the sawblade and speed chosen correspond to the material to be sawn.
•
Do not clean the machine when it is operating.
•
Adjust the cleaning brush correctly and clean it on a regular basis.
•
For diagonal cuts on a tilted table, mount the parallel guide on the lower table.
•
Never use the safety device for transport purposes.
•
Utilise the push stick when working on the machine.
Summary of Contents for RBS-5518
