3
spEcIfIcAtIONs
Air Nibbler
Model number
RA-N-B
Average air consumption
335 L/min @
6.3 bar (90 psi)
No-load speed
3000 spm
Maximum working pressure
6.3 bar (90 psi)
Weight
0.8 kg
Air inlet size
6.35 mm (1/4”)
Air hose ID
9.52 mm (3/8”)
Maximum cutting thickness
1.0 mm
Recommended cutting material Zinc plated steel,
roofing steel
Recommended material
hardness
HRB<70
A-weighted sound pressure
level
78dB(A), k=3dB
Sound power level
89dB(A), k=3dB
Vibration value
4.0 m/s
2
Uncertainty
1.5 m/s
2
Noise emission values are in accordance with EN ISO
4871 and EN ISO 15744, and tested at no load.
Vibration emission values are in accordance with EN ISO
28927-7, and tested with load.
Replacement parts
Cutter, OD6.5 x L48.6
079081001004
INtENDED UsE
The product is intended for free-style cutting of zinc plated
steel or roofing steel with maximum thickness of 1.0 mm
and material hardness of HRB<70.
Use the product only for its intended purpose.
REsIDUAL RIsks
Even if you are operating this product in accordance
with all the safety requirements, potential risks of injury
and damage remain. The following dangers can arise in
connection with the structure and design of this product:
1. Health defects resulting from vibration and noise
emission if the product is being used over long periods
of time or not adequately managed and properly
maintained.
–
Wear hearing protection and limit operating time.
–
Do not use damaged equipment. If abnormal
noise, vibration or air leak occurs, stop using
the product and have the product inspected and
corrected before use. If abnormality continues,
send the product to an authorised service centre
for repair.
2. Injuries and damage to property due to broken cutting
attachments or the sudden impact of hidden objects
during use.
–
To prevent serious personal injury, always wear
safety equipment such as heavy-duty work gloves,
non-skid safety shoes, hardhat, safety goggles,
safety mask, hearing protection, protective work
clothes, etc. before use. Inspect workpiece and
tool for hidden objects before operation.
3. Danger of injury and property damage caused by
flying objects.
–
Prior to operation, protect other people and
property in the work area from flying debris by
providing barriers or shields. Wear appropriate
personal protective equipment.
AssEMBLy
AIR sUppLy sEt Up
■
Ensure the trigger is not depressed before connecting
to the air supply.
■
Connect the product to a quick coupler.
■
Attach the air hose to the compressor's air outlet. Then
connect the other end to the quick coupler attached to
the product.
NOtE:
The air hose must be long enough to reach
the work area with enough extra length to allow free
movement while working.
■
Turn on the air compressor according to the
manufacturer's instructions. Allow it to build up
pressure until it cycles off.
■
Adjust the air compressor's output regulator to not
more than 6.3 bar (90 psi).
■
The minimum hose diameter should be 9.52 mm
(1/4”) I.D. and the fittings must have the same inside
dimensions.
■
Check for leaks in the air connections. Repair as
needed.
■
Keep hose away from heat, oil and sharp edges. Check
hose for wear, and make sure that all connections are
secure.
■
If the product will not be used, turn off and disconnect
the air supply. Discharge any residual air pressure to
prevent accidental operation.
OpERAtION
pREpARAtION
■
Designate a work area which is clean and well lit.
Prevent access by children and animals.
