18
English(original instructions)
EN
FR
DE
ES
IT
PT
NL
SV
DA
NO
FI
HU
CS
RU
RO
PL
SL
HR
ET
LT
LV
SK
BG
plastic fitting and goes on the spout at the bottom of
the gun.
■
Grasp the plastic fitting and slide onto the spout
until it clicks into place.
■
To remove, depress the latch on top of the fitting
and remove the hose from the spout.
■
The high pressure hose has a metal connection and
slides into the opening at the top of the gun.
■
Grasp the hose lock and pull outward to clear the
way for the high pressure hose to be inserted.
■
Insert the high pressure hose all the way into the
hole.
■
Push the hose lock fully back into the handle to
hold the high pressure hose in place.
CONNECTING THE GARDEN HOSE TO THE
PRESSURE WASHER
See Figure 7.
The water supply must come from a water main. NEVER
use hot water or water from ponds, lakes, etc. Before
connecting the garden hose to the pressure washer:
■
Run water through the garden hose for 30 seconds to
clean any debris from the hose.
■
Inspect the filter screen in the end of the pressure
washer intake.
■
If the filter is damaged, do not use the machine
until the screen has been replaced.
■
If the filter is dirty, clean it before connecting the
garden hose to the machine.
CAUTION:
When connecting the appliance to the water supply
mains (not public drinking water supply mains),
please observe the local regulations of local boards
or local water supplier.
To ensure that there is no feedback of contaminant
into the water supply, the appliance must not be
connected directly to the public drinking water
supply mains.
If the appliance is connected to potable water
mains, backflow prevention devices should be
incorporated in or fixed to the water supply system.
The installation should be accepted by local boards
or water supplier and should be conducted by
professional technical personnel. The backflow
prevention devices should be appropriate to fluid
categories and comply with the requirement to
avoid back siphonage according to EN 60335-2-79/
A2: 2007.
To connect the garden hose to the pressure washer:
■
Uncoil the garden hose.
NOTE:
There must be a minimum of 3 metres of
unrestricted garden hose between the pressure washer
intake and the garden tap.
■
With the garden tap turned completely off, attach
the end of the garden hose to the coupler on the
pressure washer water intake. Tighten by hand,
water that has flown through backflow preventers is
considered to be non-potable.
OPERATION
Applications
This pressure washer can be used for the purposes listed
below:
■
Removing dirt and mould from decks, cement patios,
and walls.
■
Cleaning cars, boats, motorcycles, outdoor furniture
and barbeques.
ADDING DETERGENT TO THE PRESSURE WASHER
See Figure 8.
Use only detergents designed for pressure washers;
household detergents, acids, alkalines, bleaches,
solvents, flammable material, or industrial grade solutions
can damage the pump. Many detergents may require
mixing prior to use.
Prepare cleaning solution as instructed on the solution
bottle.
■
Disconnect pressure washer from power supply.
■
Place pressure washer upright on a flat surface.
■
Remove cap from detergent tank.
■
Pour detergent into tank until it reaches the maximum
fill level located on the unit.
NOTE:
Use a funnel, if needed, to prevent accidental
spilling of the detergent outside the tank. If any detergent
is spilled during the filling process, make sure the unit is
cleaned and dried before proceeding.
■
Reinstall cap.
STARTING AND STOPPING THE PRESSURE
WASHER
See Figure 9.
CAUTION:
Do not run the pump without the water supply
connected and turned on.
■
Connect the garden hose.
■
Turn the garden hose on then squeeze the high
pressure trigger to relieve air pressure. Once a
steady stream of water appears, release the trigger.
■
After ensuring the switch is in the OFF position,
connect the pressure washer to the power supply.
■
Press
ON ( I )
on the switch to start the motor.
RPW120HS-25lgs.indd 18
RPW120HS-25lgs.indd 18
09-10-28 10:59
09-10-28 10:59
