background image

Page 16

OPERATION

BIT STORAGE

See Figure 14.

When not in use, the bit provided with this drill can be placed
in the storage area located on the base of the drill.

ELECTRIC BRAKE

This drill has an electric brake. When the trigger switch is
released, the chuck stops turning. When the brake is
functioning properly, sparks will be visible through the vent
slots on the housing.  This is normal and is the action of the
brake.

TO INSTALL BATTERY PACK

Place the direction of rotation selector in center position.
See Figure 10.

Place the battery pack in your drill. Align raised rib on
battery pack with groove in drill's battery port.
See Figure 13.

Make sure the latches on each side of your battery pack
snap in place and that battery pack is secured in drill
before beginning operation.

TO REMOVE BATTERY PACK

Place the direction of rotation selector in center position.
See Figure 10.

Locate latches on side of battery pack and depress both
sides to release battery pack from your drill.
See Figure 13.

■  

Remove battery pack from your drill.

CAUTION:

When placing battery pack in your drill, be sure raised
rib on battery pack aligns with groove in drill's battery
por t and latches snap in place properly. Improper
assembly of battery pack can cause damage to internal
components.

Fig. 13

DEPRESS LATCHES TO

RELEASE BATTERY PACK

BATTERY

PACK

BATTERY

PORT

LATCHES

Fig. 14

Summary of Contents for HP1830M





















Reviews: