![background image](http://html1.mh-extra.com/html/ryobi/etms1825hg/etms1825hg_original-instructions-manual_1506476004.webp)
2
English
damage.
■
Select the correct blade for the material to be cut.
■
Observe the maximum speed marked on the saw blade.
■
Use a holder or wear gloves when handling a saw
blade.
■
Ensure the saw blade is mounted correctly before use.
■
Make sure the blade rotates in the correct direction.
Keep the blade sharp.
■
Do not use blades of larger or smaller diameter than
recommended. Do not use any spacers to make the
blade fit onto the spindle.
■
Consider applying specially designed noise-reduction
blades.
■
Do not use HSS blades.
■
Do not use cracked or damaged saw blades.
■
Raise the blade from the kerf in the workpiece prior to
releasing the switch.
■
Ensure the arm is securely fixed when performing bevel
cuts.
■
Do not wedge anything against the fan to hold the motor
shaft.
■
The blade guard on your saw will automatically raise
when the arm is brought down, it will lower over the
blade when the arm is raised. The guard can be raised
by hand when installing or removing saw blades or
when inspecting the saw. Never raise the blade guard
manually unless the saw is switched off.
■
Keep the surrounding area of the machine well
maintained and free of loose materials, such as chips
and cut-offs.
■
Periodically check that the motor air slots are clean and
free of chips.
■
Disconnect the machine from the mains before carrying
out any maintenance work or when changing the blade.
■
Never perform any cleaning or maintenance work when
the machine is still running and the head is not in the
rest position.
■
When possible, always mount the machine to a bench.
■
When performing mitre, bevel or compound mitre cuts,
adjust the sliding mitre fence to ensure the correct
clearance for the application.
■
Refrain from removing any cut-offs or other parts of
the workpiece from the cutting area while the saw is
running.
■
Before work, check that the machine is placed on an
even surface with sufficient stability.
■
Never cut light alloy, especially magnesium.
■
Do not use any abrasive or diamond discs.
■
In case of an accident or machine failure, immediately
turn the machine off and disconnect machine from the
power source.
■
Report the failure and mark the machine to prevent
other people from using the defective machine.
■
When the saw blade is blocked due to abnormal feed
force during cutting, turn the machine off and disconnect
it from power supply. Remove the workpiece and
ensure that the saw blade runs free. Turn the machine
on and start new cutting operation with reduced feed
force.
■
Ensure that your position is always left or right of the
cutting line.
■
Provide adequate general or localized lighting.
■
Ensure the operator is adequately trained in use,
adjustment and operation of the machine.
■
Turn the machine off when unattended.
■
Connect the saw to a dust collection when sawing
wood. Always consider factors influencing exposure
of dust such as type of material to be machined (chip
board produces more dust than wood), adjustment
of saw blade, adjustment of local extraction as well
as hoods, baffles and chutes, and air velocity of dust
extractor.
■
Make sure all blade and flanges are clean and the
recessed sides of the collar are against the blade.
Tighten the arbor nut securely.
■
Keep the saw blade sharp and properly set.
■
Do not attempt to operate on anything but the
designated voltage.
■
Do not apply lubricants on the blade when it is running.
■
Ensure that bystanders do not stand behind the
machine.
■
For your own safety, always mount the machine to a
work bench using bolts.
■
Always use blades with correct size and shape of
arbour holes. Blades that do not match the mounting
hardware of the saw will run eccentrically, causing loss
of control.
■
Use only blades specified in this manual, complying
with EN 847-1.
ADDITIONAL SAFETY RULES FOR TABLE SAW MODE
■
Replace the kerf plate when worn.
■
Never use your saw without the kerf plate.
■
Ensure the table is securely fixed.
■
When performing vertical straight cross-cuts, adjust the
sliding fence correctly to ensure a clearance of 5 mm
(maximum) between the saw blade and the fence.
■
Adjust the sliding fence correctly to avoid contact with
the upper guard.
■
Never cut when riving knife and/or upper guard are
removed.
■
Make sure the riving knife is adjusted to the correct
distance from the blade (5 mm maximum).
■
Always use the push stick. Never cut workpieces
smaller than 30 mm. Never place hands closer than 150
mm from the saw blade while cutting.
■
Always keep the push stick in its place when not in use.
Summary of Contents for ETMS1825HG
