![background image](http://html1.mh-extra.com/html/ryobi/ems2026scl/ems2026scl_user-manual_1506454032.webp)
OPERATION
Bevel angle
Type of cut
setting
33.85°
Left side, inside corner
1. Top edge of molding against fence
2. Mitre table set right 31.62°
3. Save left end of cut
33.85°
Right side, inside corner
1. Bottom edge of molding against fence
2. Mitre table set left 31.62°
3. Save left end of cut
33.85°
Left side, outside corner
1. Bottom edge of molding against fence
2. Mitre table set left 31.62°
3. Save right end of cut
33.85°
Right side, outside corner
1. Top edge of molding against fence
2. Mitre table set right 31.62°
3. Save right end of cut
CUTTING WARPED MATERIAL (Fig. 38 & 39)
When cutting warped material, always make sure it is
positioned on the mitre table with the convex side against
the fence (13) as shown in figure 38.
If the warped material is positioned the wrong way as
shown in figure 39, it will pinch the blade near the
completion of the cut.
WARNING
To avoid a binding condition and to avoid serious
personal injury, never position the concave edge
of bowed or warped material against fence.
LASER
LASER BEAM (Fig. 40)
The beam from the laser shows precisely where the
blade will cut the workpiece.
The laser beam can be switched on as required:
A. Press laser on/off switch to turn the laser on and press
the switch again to turn the laser off.
B. The network cable supplies power to the laser.
The laser beam should be aligned before being used
for the first time.
■
Set bench to angle position 0°.
■
Loosen off laser-alignment screw slightly.
■
Switch the laser on and align the beam so that it
points exactly at the 0° gauge mark of mitre cut
adjuster.
■
Retighten screw before use.
MAINTENANCE
WARNING
When servicing, use only identical Ryobi
replacement parts. Use of any other part may
create a hazard or cause product damage.
GENERAL
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, carbon dust, etc.
WARNING
Do not at any time let brake fluids, gasoline,
petroleum based products, penetrating oils, etc.
come into contact with plastic parts. They contain
chemicals that can damage, weaken or destroy
plastic.
It has been found that electric tools are subject to
accelerated wear and possible premature failure when
they are used on fibreglass boats, cars, wallboard,
spackling compounds, or plaster. The chips and grindings
from these materials are highly abrasive to electric tool
parts such as bearings, brushes, commutators, etc.
Consequently, it is not recommended that this tool be
used for extended work on any fibreglass material,
wallboard, spackling compounds, or plaster. During any
use on these materials it is extremely important that the
tool is cleaned frequently by blowing with air. Respiratory
protection must be used when performing this task.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit
under normal operating conditions. Therefore, no further
lubrication is required.
22
GB
F
D
E
English
I
P
NL
S
DK
N
FIN
GR
H
CZ
RUS
RO
PL
EMS-2026-SCL_17 lgs 22/03/06 16:00 Page 22
Summary of Contents for EMS2026SCL
