![background image](http://html1.mh-extra.com/html/ryobi/csd42l/csd42l_user-manual_1505642005.webp)
2
English
GB
FR
DE
ES
IT
NL
PT
DK
SE
FI
NO
RU
PL
CZ
HU
RO
LV
LT
EE
HR
SI
SK
GR
TR
OPERATION
D I R E C T I O N O F R O TAT I O N S E L E C TO R
(FORWARD / REVERSE / CENTER LOCK)
See Figure 3.
The direction of bit rotation is reversible and is controlled
by a selector located above the switch trigger. With
the screwdriver held in normal operating position, the
direction of rotation selector should be positioned to the
left of the switch trigger for forward motion. The direction
is reversed when the selector is to the right of the switch
trigger.
Setting the switch trigger in the
OFF
(center lock) position
helps reduce the possibility of accidental starting when
not in use.
CAUTION
To prevent gear damage, always allow the collet
to come to a complete stop before changing the
direction of rotation.
To stop the screwdriver, release the switch trigger and
allowthe collet to come to a complete stop.
NOTE:
The screwdriver will not run unless the direction
of rotation selector is pushed fully to the left or right.
TWO-SPEED GEAR BOX
See Figure 4.
The screwdriver has a two-speed gear box designed for
LO
or
HI
speeds. A slide switch is located on top of the
screwdriver to select either
LO
or
HI
speed. When using
screwdriver in the
LO
speed range, speed will decrease
and unit will have more power and torque.When using
screwdriver in the
HI
speed range, speed will increase
and unit will have less power and torque. When drilling
use 1/4 in. hex shank drill bits only. Maximum drill size
is 1/4 in.
Use the
HI
speed setting to drill holes, and use the
LO
speed setting for driving screws.
TO LOAD/RELEASE BITS
See Figure 5.
The SPE™ SYSTEM on the screwdriver is
a quick change chuck designed to accept any 1/4 in.
hex bits. Insert the bit into the chuck and push as far as
possible until the chuck locks onto the bit. To remove
a bit, push rubber collar forward, and then pull the bit
straight out of the chuck.
ADJUSTABLE TORQUE CLUTCH
This screwdriver is equipped with an adjustable torque
clutch for driving different types of screws into different
materials. The proper setting depends on the type of
material and the size of screw you are using.
ADJUSTING TORQUE
See Figure 6.
There are twenty-four torque indicator settings located on
the front of the screwdriver.
Q
Select the gear selection setting to
HI
or
LO
speed.
Q
Rotate the adjusting ring to the desired setting.
1 - 4
For driving small screws (
HI
or
LO
speed)
5 - 8
For driving screws into soft material
(
LO
speed)
9 - 12
For driving screws into soft and hard
materials (
LO
speed)
13 - 16
For driving screws in hard wood (
LO
speed)
17 - 24
For driving large screws (
LO
speed)
OVERLOAD PROTECTION DEVICE
The tool has an overload protection device. The tool will
stop if the spindle is locked for several seconds while the
trigger is on. If this happens, release the trigger, then wait
for a few seconds before you resume operation. To avoid
this situation, do not force the tool.
LED WORKLIGHT
See Figure 7.
The screwdriver has a built-in LED worklight. This feature
is convenient when working in close or tight areas where
additional light is needed. Whenever the switch trigger is
depressed, the LED worklight will illuminate.
NOTE:
The LED worklight will go off when overload
protection causes the tool to stop. The light will come
on again when the trigger is depressed and operation
resumes.
MAINTENANCE
WARNING
When servicing, use only identical replacement
parts. Use of any other part may create a hazard
or cause product damage.
961067240-02_CSD42L_EU.indd Sec1:2
961067240-02_CSD42L_EU.indd Sec1:2
1/5/10 11:33:22 AM
1/5/10 11:33:22 AM
Summary of Contents for CSD42L
Page 85: ...961067240 02...