background image

13 - English

OPERATION

BEVEL CUTTING

See Figures 19 - 21, page 18.

To make the best possible cut, follow these helpful hints.

 

Align the line of cut with the inner blade guide notch on 
the base when making 45° bevel cuts.

 

Make a trial cut in scrap material along a guideline to 
determine how much you should offset the guideline on 
the cutting material.

 

Adjust the angle of the cut to any desired setting between 
zero and 51.5°. Refer to 

To Adjust Bevel Setting

 

next.

TO ADJUST BEVEL SETTING

See Figures 19 - 20, page 18.

 

Unplug the saw.

 

Loosen bevel lock knob.

 

Rotate motor housing end of saw until you reach desired 
angle setting on bevel scale.

 

Tighten bevel lock knob securely.

wARNING:

Attempting a bevel cut without having the bevel  lock knob 
 securely tightened can result in serious injury.

TO BEVEL CUT

See Figure 21, page 18.

 

Hold the saw firmly with both hands as shown.

 

Rest the front edge of the base on the workpiece.

 

Start the saw and let the blade reach full speed.

 

Guide the saw into the workpiece and make the cut.

 

Release the switch and allow the blade to come to a 
complete stop.

 

Lift the saw from the workpiece.

POCkET CUTTING

See Figure 22, page 18.

wARNING:

Always adjust bevel setting to zero before making a 
pocket cut. Attempting a pocket cut at any other setting 
can result in loss of control of the saw possibly causing 
serious injury.

 

Adjust the bevel setting to zero and tighten the bevel lock 
knob.

 

Set the blade to the correct blade depth setting.

 

Swing the lower blade guard up using the lower blade 
guard handle.

 NOTE: 

Always raise the lower blade guard with the handle 

to avoid serious injury.

 

Hold the lower blade guard by the handle while keeping 
your hand on the front handle as shown.

 

Rest the front of the base flat against the workpiece with 
the rear of the handle raised so the blade does not touch 
the workpiece.

 

Start the saw and let the blade reach full speed.

 

Guide the saw into the workpiece and make the cut.

wARNING:

Always cut in a forward direction when pocket cutting. 
Cutting in the reverse direction could cause the saw to 
climb up on the workpiece and back toward you.

 

Release the switch and allow the blade to come to a 
complete stop.

 

Lift the saw from the workpiece.

 

Clear corners out with a hand saw or sabre saw.

wARNING:

Never tie the lower blade guard in a raised position. 
Leaving the blade exposed could lead to serious injury.

OPTIONAL DUST NOZZLE kIT

See Figure 23, page 19.

You may purchase a dust nozzle kit, part no. 200673002, 
for use with the saw. The adaptor fits over the dust chute 
which is located on the upper blade guard. The nozzle at-
taches to the adaptor. 

NOTE:

 If you use the nozzle, you should always connect it 

to a standard vacuum hose.

To attach the dust nozzle:

 

Unplug the saw.

 

Lift lower blade guard.

 

Orient adaptor to fit into the dust chute opening on upper 
blade guard.

 

Secure adaptor with screw provided.

  Align hole in nozzle with raised lip on adaptor and snap 

into place when using a vacuum hose.

Summary of Contents for CSB143LZ

















































Reviews: