Ryobi CMS180G, Original Instructions Manual

Page: 4 / 28

Safety
4
is switched off.
■ Sawdust and splinters must not be removed while the
machine is running.
■ Never reach into the danger area of the plane of the
blade when it is running.
■ Repairs should only be carried out by authorised
service agents.
■ Always use the protective shields on the machine.
■ Do not clamp the protective swing guard.
■ Do not use saw blades which are damaged or deformed.
■ Replace the table insert when worn.
■ Do not use saw blades not corresponding to the key
data given in these instructions for use.
■ The protective cover should only open when the
machine is lowered to the workpiece.
■ Do not use saw blades made of high-speed steel.
■ Any faults with the machine, including any related to
the safeguard or the saw blades, must be reported to
the persons in charge of safety as soon as the faults
are discovered.
■ It is necessary to select a saw blade which is suitable
for the material being cut.
■ Never use the mitre saw to cut materials other than
those specified in the instruction manual.
■ The handle lock must always be engaged when
transporting the mitre saw.
■ Only use the saw with guards in good working order
and properly maintained, and in position.
■ Keep the floor area free of loose material e.g., chips
and cut-offs.
■ Only use saw blades which have been properly
sharpened. It is essential to adhere to the maximum
speed specified on the saw blade.
■ Do not use any flanges other than those supplied or
indicated in the instruction manual to secure the saw
blade.
■ Refrain from removing any cut-offs or other parts of the
workpiece from the cutting area whilst the machine is
running and the saw head is not in the rest position.
■ Ensure that the machine is always stable and secure
(e.g., fixed to a bench).
■ Long workpieces must be adequately supported.
■ Do not use cracked or distorted saw blades.
■ Before using the tool please read the instructions. If
possible have the tool demonstrated.
■ The dust produced when using this tool may be harmful
to health. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust
thoroughly, e.g., with a vacuum cleaner.
■ Stock having a round or irregular cross section (such
as firewood) must not be cut, as it cannot be securely
held during cutting. When sawing thin stock layered on
edge, a suitable auxiliary fence must be used for firm
support.
■ Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
■ Do not stare directly at the laser beam.
■ Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
■ Any repairs must only be carried out by the laser
manufacturer or authorized service agent.
■ Do not replace the laser with a different type.
INTENDED USE
■ The mitre saw can be used for sawing solid wood,
bonded wood, glued veneer, materials similar to wood,
and plastics.
■ Do not use this product in any other way as stated for
normal use.
LASER SAFETY
■ Do not stare into beam during operation.
■ Do not project the laser beam directly into the eyes of
others. Serious eye injury could result.
■ Do not place the laser in a position, that may cause
anyone to stare into the laser beam intentionally or
unintentionally.
■ Do not use optical tools to view the laser beam.
■ Do not operate the laser around children or allow
children to operate the laser.
■ Do not attempt to repair the laser device by yourself.
■ Do not attempt to change any parts of the laser device
by yourself.
■ Any repairs must only be carried out by the laser
manufacturer or authorized service agent.
■ Do not replace the laser with a different type.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
of as waste. The machine, accessories
and packaging should be sorted for
environmental-friendly recycling.
SYMBOL
Safety alert
V Volts