![background image](http://html.mh-extra.com/html/ryobi/bs904/bs904_operators-manual_1506358009.webp)
9 — English
ASSEMBLY
LOOSE PARTS LIST
See Figure 4, page 18.
The following items are included with the saw:
Key
No. Description
Qty.
A
Saw Table ............................................................1
B
Miter Gauge .........................................................1
C
Hex key, 2 mm .....................................................1
D
Hex key, 4 mm .....................................................1
E Washer .................................................................1
F
Table Lock Lever .................................................1
Operator’s Manual (not shown) ...........................1
UNPACKING
This product requires ass
embly.
Carefully lift the saw from the carton and place on a level
work surface.
WARNING:
Do not use this product if any parts on the Loose Parts
List are already assembled to your product when you
unpack it. Parts on this list are not assembled to the
product by the manufacturer and require customer instal-
lation. Use of a product that may have been improperly
assembled could result in serious personal injury.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipp
ing.
NOTE:
This saw has been shipped with no blade tension.
Do not turn this saw on until blade tension has been
properly set.
Do not discard the packing material until you have carefully
inspected and satisfactorily operated the tool.
If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
MOUNTING BAND SAW TO WORKBENCH
If the band saw is to be used in a permanent location, the
band saw must be mounted to a firm supporting surface
such as a workbench. Four bolt holes have been provided in
the saw’s base for this purpose. Bolts should be of sufficient
length to accommodate the saw base, lock washers, hex
nuts, and the thickness of the workbench. Tighten all four
bolts securely.
Carefully check the workbench after mounting to make
sure that no movement can occur during use. If any tipping,
sliding, or walking is noted, secure the workbench to the
floor before operating.
Place band saw on the workbench. Using the saw base
as a pattern, locate and mark the holes where the band
saw is to be mounted.
Drill holes through the workbench.
Place band saw on the workbench aligning holes in the
saw base with the holes drilled in the workbench.
Insert bolts (not included) and tighten securely with lock
washers and hex nuts (not included).
NOTE:
All bolts should be inserted from the top. Install
the lock washers and hex nuts from the underside of the
bench.
CLAMPING BAND SAW TO WORKBENCH
See Figure 5, page 18.
If the band saw is to be used as a portable tool, it is
recommended that you fasten it permanently to a mounting
board that can easily be clamped to a workbench or other
supporting surface. The mounting board should be of
sufficient size to avoid tipping of saw while in use. Any
good grade plywood or chipboard with a 3/4 in. thickness
is recommended.
If lag bolts are used, make sure they are long enough to
go through holes in the saw base and material the saw is
being mounted to. If machine bolts are being used, make
sure bolts are long enough to go through holes in the saw
base, the material being mounted to, and the lock washers
and hex nuts.
NOTE:
It may be necessary to countersink hex nuts and
washers on bottom side of mounting board.
Mount saw to board using holes in saw base as a template
for hole pattern. Locate and mark the holes where the
band saw is to be mounted.
Follow the last three steps in the section
Mounting Band
Saw to Workbench,
shown above.
Summary of Contents for BS904
Page 53: ...23 NOTES NOTES NOTAS ...
Page 54: ...24 NOTES NOTES NOTAS ...
Page 55: ...25 NOTES NOTES NOTAS ...