background image

4

English

 

OPERATION

TO INSTALL BATTERY PACK

See Figure 2.

 

Place the direction of rotation selector in the center 

position.

 

Insert the battery pack into the product as shown.

 

Make  sure  the  latches  on  each  side  of  the  battery 

pack snap in place and that battery pack is secured in 

the product before beginning operation.

TO REMOVE BATTERY PACK

 

Depress the latches on each side of the battery pack.

 

Remove the battery pack from the drill.

 

WARNING

 Battery  products  are  always  in  operating 

condition. Therefore,  the  switch  should  always 

be  locked  when  not  in  use  or  carrying  at  your 

side.

 

CAUTION

 The metal surface may become hot during use. 

Avoid contact with it to avoid possible burn injury.

TRIGGER SWITCH

See Figure 3.

To turn the drill 

ON

, depress the trigger switch. To turn it 

OFF, release the trigger switch.

VARIABLE SPEED

The variable speed trigger switch delivers higher speed 

with  increased  trigger  pressure  and  lower  speed  with 

decreased trigger pressure.

NOTE:

 You might hear a whistling or ringing noise from 

the  switch  during  use.  Do  not  be  concerned;  this  is  a 

normal part of the switch function.

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE/CENTER LOCK)

See Figure 3.

The direction of bit rotation is reversible and is controlled 

by a selector located above the trigger switch. With the 

drill  held  in  normal  operating  position,  the  direction  of 

rotation  selector  should  be  positioned  to  the  left  of  the 

trigger switch for forward drilling. The drilling direction is 

reversed when the selector is to the right of the trigger 

switch.
Setting the trigger switch in the 

OFF

 (center lock) position 

helps reduce the possibility of accidental  starting  when 

not in use.

 

CAUTION:

 To prevent gear damage, always allow the chuck 

to come to a complete stop before changing the 

direction of rotation.

To stop, release trigger switch and allow the coupler to 

come to a complete stop.

BUILT-IN COUPLER

See Figure 4.

The  tool  has  a  built-in  coupler. The  coupler  has  been 

designed to accept 6.35 mm hex bits.

INSTALLING BITS

See Figure 4.

 

Lock trigger switch on the tool by placing the direction 

of rotation selector in center position.

 

Slide the coupler forward and hold in position.

 

Insert bit straight into coupler.

 

Slide the coupler back slowly and release.

REMOVING BITS

See Figure 4.

 

Lock trigger switch or the drill by placing the direction 

of rotation selector in center position.

 

Slide the coupler forward and hold in position.

 

Pull bit straight out of coupler.

 

WARNING

 Make  sure  the  bit  is  secured  in  the  coupler 

before using the impact driver. Failure to do so 

could cause serious personal injury.

 

WARNING

 Do  not  drive  a  screw  where  there  is  likely  to 

be  hidden  wiring  behind  the  surface.  Contact 

with a “live” wire will make exposed metal parts 

of the tool “live”  and shock the operator. If you 

must  drive  a  screw  where  hidden  wire  may  be 

present,  always  hold  tool  by  insulated  gripping 

surfaces (handle) when performing the operation 

to  prevent  a  shock  to  the  operator,  as  seen  in 

figure 5.

 

CAUTION:

 The impact driver is not designed to be used as 

a drill.

BID1821_SAA-v4.indd   4

22/01/2010   6:19 PM

Summary of Contents for BID1821










Reviews: