![background image](http://html1.mh-extra.com/html/ryobi/ajp-2200gq/ajp-2200gq_owners-operating-manual_1505998016.webp)
1
Discarding the machine
Carry out the following safety measures immediately, if you are no longer going to use the machine:
• Pull out the plug and make the machine inoperable.
• Store the machine in an area that cannot be reached by children.
• Do not use any parts from the used machine as replacement parts.
• Disassemble the machine and discard the individual parts in accordance with the regulation neforced in your area.
SAVE THESE INSTRUCTIONS
Troubleshooting
When used as self-priming
Fault
Cause
Remedy
Low water pressure.
(Weak water stream)
(Water comes out in spurts)
Strainer is not completely submerged
(Because the water source decreases
as you spray, the strainer may not be
completely submerged as the water
source depletes.)
M a ke s ure t hat t h e s t ra i n er i s
completely submerged into the water.
The strainer and/or water suction
filter have become clogged. (Water
pressure suddenly decreases when
the filters become partially clogged
with debris.)
Clean the strainer, water suction filter,
and the water supply filter.
Filter all foreign matter (sand, dirt,
debris, etc) from the water source
before using it for self suction.
The valve dial has not been closed
completely.
Turn the valve dial all the way to the
closed position.
The motor continues to run when the
spray handle trigger is released.
The valve dial has not been closed
completely.
Turn the valve dial all the way to the
closed position.
The motor suddenly starts up (In
intervals less than minutes apart)
even when the spray handle trigger
has not been depressed.
The valve dial has not been closed
completely.
Turn the valve dial all the way to the
closed position.
Self suction operation fails
(Does not pump from the water
source)
The strainer is not submerged into
the water. (Because the water source
decreases as you spray, the strainer
may not be completely submerged as
the water source depletes.)
M a ke s ure t hat t h e s t ra i n er i s
completely submerged into the water.
The self suction height is over 1 meter
(3 feet)
(Because the water source decreases
as you spray, the suction height may
increase to over 1 meter (3 feet) as the
water source depletes.)
Add water to the source to decrease
the suction height to below 1 meter (3
feet)
The strainer and/or water suction filter
have become clogged.
Clean the strainer, water suction filter,
and the water supply filter.
Filter all foreign matter (sand, dirt,
debris, etc) from the water source
before using it for self suction.
The pressure adjustment dial is not
set to the self suction position
Set the pressure adjustment dial to
the self suction position
The valve dial is not open
Open the valve dial
Self suction failure with water leakage
or air intake from the water suction
filter.
The water suction filter may not be
properly attached to the connection
port.
Remove the water suction filter from
the main unit and reattach it correctly
following the instructions in step C of
the WARNING under “Attach the water
suction filter by screwing it onto the
connection port”.
The filter unit is not properly inserted
into the water suction filter.
Summary of Contents for AJP-2200GQ
