background image

1

Discarding the machine

Carry out the following safety measures immediately, if you are no longer going to use the machine:

•  Pull out the plug and make the machine inoperable.

•  Store the machine in an area that cannot be reached by children.

•  Do not use any parts from the used machine as replacement parts.

•  Disassemble the machine and discard the individual parts in accordance with the regulation neforced in your area.

SAVE THESE INSTRUCTIONS

Troubleshooting 

Self suction (AJP-1700VGQ)

Fault

Cause

Remedy

Low water pressure.

(Weak water stream)

(Water comes out in spurts)

Strainer is not completely submerged 

(Because the water source decreases 

as you spray, the strainer may not be 

completely submerged as the water 

source depletes.)

Make  sure  that  the  strainer  is 

completely submerged into the water.

The strainer and/or water suction filter 

have become clogged. (Water pressure 

suddenly decreases when the filters 

become partially clogged with debris.)

Clean the strainer, water suction filter, 

and the water supply filter.

Filter  all  foreign  matter  (sand,  dirt, 

debris,  etc)  from  the  water  source 

before using it for self suction. 

The valve dial has not been closed 

completely.

Turn the valve dial all the way to the 

closed position.

The motor continues to run when the 

spray handle trigger is released.

The valve dial has not been closed 

completely.

Turn the valve dial all the way to the 

closed position.

The  motor  suddenly  starts  up  (In 

intervals less than  minutes apart) 

even when the spray handle trigger 

has not been depressed. 

The valve dial has not been closed 

completely. 

Turn the valve dial all the way to the 

closed position.

Self suction operation fails

(Does not pump from the water source)

The strainer is not submerged into 

the water. (Because the water source 

decreases as you spray, the strainer 

may not be completely submerged as 

the water source depletes.)

Make  sure  that  the  strainer  is 

completely submerged into the water.

The self suction height is over 1 meter 

(3 feet)

 (Because the water source decreases 

as you spray, the suction height may 

increase to over 1 meter (3 feet) as the 

water source depletes.) 

Add water to the source to decrease 

the suction height to below 1 meter (3 

feet)

The strainer and/or water suction filter 

have become clogged.

Clean the strainer, water suction filter, 

and the water supply filter.

Filter  all  foreign  matter  (sand,  dirt, 

debris,  etc)  from  the  water  source 

before using it for self suction.

The pressure adjustment dial is not set 

to the self suction position

Set the pressure adjustment dial to the 

self suction position

The valve dial is not open

Open the valve dial

Self suction failure with water leakage 

or  air  intake  from  the  water  suction 

filter.

The  water  suction  filter  may  not  be 

properly attached to the connection 

port. 

Remove the water suction filter from 

the main unit and reattach it correctly 

following the instructions in step C of 

the WARNING under “Attach the water 

suction filter by screwing it onto the 

connection port”.

The filter unit is not properly inserted 

into the water suction filter.

Summary of Contents for AJP-1700V

















Reviews: