10
When the trigger is depressed, the motor resumes and
pressurized spray is ejected from the nozzle.
WARNING!
• Maneuver the spray handle hose carefully over rough
surfaces such as gravel, broken concrete, or crushed
stone.
• Avoid excessive friction that could damage the spray
handle hose when moving around objects such as
fences, blocks, or bricks.
• Ensure that the spray handle hose is straight and free
of any kinks or twists before using.
• During initial use, the spray stream may be intermittent
and erratic while air is being dispelled from within the
pump and hose. When this occurs, continue to depress
the trigger until the spray stream stabilizes.
• Adjust the water pressure as needed. (See “Adjusting
Water Pressure”)
• Be sure to turn the main switch to the OFF position
when leaving the unit unattended.
• When spraying, ensure that the spray handle trigger
is always depressed and released for intervals lasting
longer than seconds in duration.
Malfunction of the pressure switch may occur from
spray intervals lasting less than seconds.
After Use
1. Turn the main switch to the OFF position.
. Turn the water faucet off.
3. Depress the spray handle trigger until all water has
stopped flowing from the nozzle.
. Pull the hose joint coupler forward to release the water
supply hose from the water connector.
. Depress the spray handle safety lock button to lock the
trigger.
6. Remove the spray handle hose from the main unit.
7. Remove remaining water from the main unit
Turn the main switch to the ON position for 1- seconds
to discharge excess water from the spray handle hose
connection port.
WARNING!
Exercise caution as the released of excess
water is highly pressurized
WARNING!
Leaving the main switch on for longer than
seconds may damage the unit. Be sure to turn the main
switch off immediately.
8. Unplug the power cord.
9. Remove the water supply hose from the faucet.
10. Remove the spray handle hose from the spray handle.
WARNING!
Remove all excess water from the main unit, spray handle
hose, spray handle and nozzles especially in cold weather.
Storing the unit in cold temperatures without removing all
excess water may damage the unit and cause malfunction.
Self suction Mode (AJP-1700VGQ)
Attaching the Self suction kit
1.
Attaching the water suction filter to the water supply port.
• If the water supply hose () or the water connectors(9)
are attached, remove them. (Fig.19)
WARNING!
The water supply hose () is not used in self
suction mode.
WARNING!
Before attaching the self suction kit,
thoroughly clean the water suction filter (12), the main
unit filter (18), and the strainer (). Accumulation of
sand, dirt and other debris may result in decreased
pressure and damage to the unit. (Fig.3,33,3)
• Attach the water suction filter (12) by screwing it onto the
connection port. (Fig.0)
WARNING!
a. Ensure that the water supply port and water suction
filter unit contain filters (18,21). Without filters, foreign
matter may enter and damage the pump.
b. Rubber washers (3,) are attached inside the water
connectors and inside the water suction filter.
Be careful not to lose these washers when removing
them.
c. Failure to draw water after the water suction hose
has been connected, leakage after water flow has
been initiated, or seepage under the main unit may be
caused by the following:
• The water suction filter connection is loose.
• The water suction filter is not securely connected to
the connection port.
• Leakage between the filter case and the rubber
washer is occurring due to the improper insertion of
the filter unit into the water suction filter.
If any of the above situations have been discovered,
remove the water suction filter from the main unit and
reattach it according to the following instructions.
Loosen the filter cap and ensure that the filter unit
has been properly inserted into the filter case.
(Fig.0-1)
After ensuring that the filter unit has been properly
inserted into the filter case, thread the filter cap
directly onto the filter case and securely tighten.
(Fig.0-)
Thread the water suction filter directly onto the
main unit connection port and securely tighten.
(Fig.0)
If water continues to leak, ensure that all of the
connections have been securely tightened.
. Attaching the water suction hose to the water suction
filter (Fig. 21)
Insert the water suction hose (1) straight onto the water
suction filter (12) and turn the link clockwise to fasten.
Ensure that the link is tightened securely.
3. Connect the transparent hose (13) to the valve dial (19).
(Fig.)
Connect the spray handle hose (), spray handle (), and
nozzles (6 or 7) in the same manner as when using water
from the faucet (Fig.7-11)
Summary of Contents for AJP-1700V
