background image

8

OIL AND FUEL INFORMATION

Old or improperly mixed fuel are usually 
the main reasons for the unit not running
properly. Be sure to use fresh, clean fuel and
follow the instructions carefully for the proper
fuel/oil mixture.

NOTE: 

Alcohol-blended fuel absorbs moisture
(water). As little as 1% moisture in the
fuel can cause fuel and oil to separate
and form acids when stored. If this
type of fuel must be used, use fresh
fuel (less than 60 days old), and mix
according to the mixing instructions.

DEFINITION OF BLENDED FUELS

Today's fuels are often a blend of gasoline
and one or more oxygenates such as ethanol,
methanol or MTBE (ether).

USE OF BLENDED FUELS

If you choose to use a blended fuel or its use
is unavoidable, the following precautions are
recommended.
1. Always use fresh fuel mix per your

operator's manual.

2. Use the special additive STA-BIL® or 

an equivalent.

3. Always agitate the fuel mix before fueling

the unit.

4. Drain the tank and run the engine dry

before storing the unit.

USE OF FUEL ADDITIVES

The use of fuel additive, such as STA-BIL®
Gas Stabilizer or an equivalent, will inhibit
corrosion and minimize the formation of gum
deposits. Add 0.8 oz (23 ml) per gallon of fuel
per instructions on container. NEVER add fuel
additives directly to the unit's fuel tank. Using
a fuel additive can keep fuel fresh for up to six
(6) months.

CAUTION: 

For proper engine

operation and maximum reliability,
pay strict attention to the oil and 
fuel mixing instructions on the 
2-cycle oil container. Use a 32:1
fuel/oil ratio. Use 2-cycle oil. Using
improperly mixed fuel can severely
damage the engine.

WARNING:

Pressure can build up 

in the fuel tank. Loosen the fuel 
tank cap slowly to relieve any
pressure in the tank.

+

UNLEADED

GAS

RYOBI OIL

1 U.S. GALLON

+

4.0 fl. oz.

(3.8 liters)

(118 ml)

1 LITER

+

30 ml

MIXING RATIO - 32:1

WARNING:

Gasoline is extremely

flammable and its vapors can
explode if they are ignited. To avoid
serious personal injury, always stop
the engine and allow it to cool
before filling the fuel tank. Do not
smoke while filling the tank. Keep
sparks and open flames away from
the area.

OIL AND FUEL MIXING INSTRUCTIONS

Thoroughly mix the proper ratio of 2-cycle
engine oil with unleaded gasoline in a
separate fuel can, 32:1. Do not mix them
directly in the engine fuel tank. See the table
below for specific gas and oil mixing ratios.

Summary of Contents for 2075r





















Reviews: