background image

9

OPERATING INSTRUCTIONS

Fig. 6

1.

MIX OIL WITH GAS AND FILL FUEL TANK
WITH FUEL/OIL MIXTURE

per instructions

on page 8.

2. Put the 

IGNITION SWITCH IN THE “ON”

POSITION

(Fig. 5).

3.

FULLY PRESS AND RELEASE THE PRIMER
BULB 5 TO 7 TIMES. FUEL SHOULD BE
VISIBLE IN THE BULB 

(Fig. 6). 

4.

PLACE THE CHOKE LEVER IN THE
“START” POSITION 

(A) (Fig. 6).

5. 

WITH THE UNIT ON THE GROUND,
SQUEEZE THE THROTTLE TRIGGER
FULLY AND PULL THE STARTER ROPE
BRISKLY

(Fig. 7) until the engine sounds like

it wants to run (normally 2 to 5 pulls).

NOTE:

Keep the throttle trigger depressed at all

times until the engine is warmed up.

6.

PLACE THE CHOKE LEVER IN THE “RUN”
POSITION

(B) (Fig. 6). 

7.

PULL THE STARTER ROPE BRISKLY 1 TO
3 TIMES TO START THE ENGINE

(Fig. 7).

8. If the engine does not start, repeat steps 

4 through 7.

NOTE:

If the engine floods while attempting to

start the unit, place the choke lever in
the “RUN” position (B), squeeze the
throttle trigger, and pull the starter rope
briskly. The engine should start within
three (3) to eight (8) pulls.

9. Keep throttle trigger depressed for 5 to 10

seconds to warm up engine. 

NOTE:

Choking is not required when starting a 
warm engine. Start a warm engine in the 
“RUN” POSITION.

Ignition

Switch

Primer

Bulb

Run

(B)

Start

(A)

Choke

Lever

Fig. 5

Fig. 7

STARTING/STOPPING

WARNING:

Avoid accidental starting.

Be in the starting position whenever
pulling the starting rope. To avoid
serious personal injury, the operator
and unit must be in a stable position
while starting.

WARNING:

Operate this unit only

in a well-ventilated area outdoors.
Carbon monoxide exhaust fumes
can be lethal in a confined area.

10.To stop the engine, put the 

IGNITION SWITCH

IN THE "OFF" POSITION

(Fig. 5).

Summary of Contents for 2075r





















Reviews: