manualshive.com logo in svg

Ruris 425, User Manual

Share
Download
Ruris 425 User Manual Download Page 4

 
 

 

3 

1.0 Essential Checks before Commissioning and 

During Operation 

 

Make sure that: 

1. 

The circuit of the emergency stop lever is properly assembled. 

2. 

Oil quantity from the engine bath for the brush cutter 425: 100ml 

3. 

Oil quantity from the engine bath for the brush cutter 435: 120ml 

4. 

The oil used is Ruris brand: Ruris 4T/ 10W30-APISJ/CH 

5. 

Running in must be made at idle and not under load. Three tanks 

of gas at idle, no-load. 

6. 

The  reduction  gear  of  the  mowing  head  is  filled  with  graphite 

grease,  the  indicated  level  is  given  by  the  grease  located  on  the 
top of the screw from the supply area according to the installation 
mode shown below according to figure 1. 
 

 

Fig. 1 

 

 

 

Fig. 1.1

 

7. 

The  coupling,  decoupling  levers  are  working  and  respond  to 

commands by gently pulling the starter rope.  

 
8. 

Mounting of the cutter disc is properly made according to the figure 

below - fig. 1.2 

 

 

Summary of Contents for 425



























Reviews:

No comments

Brands by name

Popular brands

Load more brands