Read the following instruction first before operate the product
Caution!
This appliance contains dust hazardous to health. Emptying
and manteinance operations
, including removal of the dust
collerction means,
must only be carried out by authorized personnel
wearing suitable personal protections. Do not operate without the full
filtration system fitted
PACKAGE HANDLING INSTRUCTIONS
The machine is packaged in n. 1 box with the following dimensions and weight:
HE501 - HE901: 1570 x 980 x 550 mm
HE1101 - HE1501: 1570 X 1360 X 550 mm
made up of:
- wooden platform;
- corrugated cardboard covering;
- binding straps.
The box must be handled and stored in the upright position.
Do not place any objects on the package that weigh more and/or have a different
sized base than the package.
For packaging waste disposal attain to local regulations in
force, including recycling disposal if requested.
WARNINGS
Safety and accident prevention instructions
The machine is to be considered a centralised vacuum unit connected by a per-
manent hose to various located vacuum points.
RUPES
Spa
is not liable for any direct or indirect damages due to failure to
comply with the instructions provided in this manual.
The machine must only be used by trained and qualified personnel.
The machine must be located in a dry and well-ventilated area where air is chan-
ged at least once an hour with 50% of the total fresh air without the aid of special
ventilation systems. The temperature of the work area must be between 10°C and
35°C with humidity between 50% and 90%.
Explosion or fire hazard
- Do not vacuum explosive dust
- do not vacuum flammable or explosive liquids (i.e. petrol, thinners, etc.);
- do not vacuum aggressive liquids or substances (i.e. acids , bases, solvents,
etc.);
- do not vacuum sanding dust from surfaces treated with paints that have not
completed the catalyst cycle;
- immediately disconnect the machine from the electrical mains if dust is
discharged;
- use the fire alarm system and leave the area in the event of fire.
Specific use
The machine is high stress qualified for industrial applications according to
regulations EN55014-1 and EN60335-1.
The machine is designed to vacuum dry sanding dust with all exposure limit
values due to the work type.
The machine is equipped with a fitting for external exhaust of vacuumed and
filtered air as required by the current regional and national laws
Important safety indications.
ENGLISH
PICTOGRAPH
12
PARTS OF THE TOOL
1 - suction fitting
2 - discharge fitting
3 - door opening
3A panel screws (HE501)
4 - working pressure indicator gauge
5 - electronic command and control panel
6 - ventilation grill
7 - dust bag compartment door
8 - identification plate
9 - compressed air pressure regulator
9A - control knob
10 - condensate drain
11 - electrical power supply cable
12 - suction pump
13 - silencer
14 - suction pipe
15 - filter
16 - rotojet filter cleaning system
17 - dust bag container
18 - dust bag
19 - dust bag retaining ring
20 - main switch
21 - circuit board
22 - contactor
22A - thermal protections (HE1101 - HE1501)
23 - transformer
24 - fuses
25 - electro-valve
26 - pneumatic valve
27 - ON/OFF knob
28 - machine “on” indicator light
29 - manual mode indicator
30 - automatic mode indicator
31 - filer cleaning in operation indicator
32 - display
33 - mode selection button
34 - clean filter in manual mode button
35 - display menu button
36 - safety valve
37 - temperature sensor
38 - motor status
INSTALLATION
Warning!
The machine must be installed and started for the first time by qualified per-
sonnel!
Turbine positioning (Fig. 1)
- The machine must be positioned on a solid and level surface at the distances in-
dicated in (Fig. 1), generally installed on the same or lower work surface.
- Avoid installing the turbine higher than the work surface.
- The turbine vents (6) must be kept clean and unclogged.
- Level the turbine using the adjustment feet (Fig. 3).
- After adjustments, tighten the lock nuts (Fig. 3 A).
- Connect the turbine's left coupling to the vacuum system (Fig. 2 A) with
50 cm. of 75 internal Ø flexible tube.
- The exhaust (Fig. 2 B) can be connected with the exterior.
START-UP
Minimum power supply requisites and connections:
Electrical power supply connections:
- Three phase voltage 400 V - 50 Hz (230 V - 60 Hz); with a suitably dimensio-
ned grounding wire;
- a circuit breaker must be installed upstream from the power line according to the
instructions provided for each turbine.
Compressed air system requirements:
- Maximum working pressure: 7 bar;