background image

Ruijie  5/8-Port  Plastic  Series  Switches  Hardware  Installation  and  Reference  Guide 

 

current of the system totals 30mA. A leakage protector with 30mA rated action current supports less than ten power 

supplies  (that  is,  Action  current  of  the  leakage  protector/2/Maximum  leakage  current  of  each  power  supply 

=30/2/1.5=10). In other words, the leakage protector with 30mA rated action current supports no more than ten power 

supplies. In this case, the twenty power supplies in the system require at least two leakage protectors with 30mA 

rated action current and each leakage protector supports ten power supplies. If power supplies in a system differ in 

models, the rated leakage action current of each leakage protector divided by two is greater than the sum of maximum 

leakage current of all the power supplies. The rated leakage non-action current of a leakage protector shall be 50% 

of the leakage action current. Take a leakage protector with 30mA rated leakage action current as an example. The 

rated leakage non-action current shall be 15mA. When the leakage current is below 15mA, the protector shall not act. 

Otherwise, misoperation may easily occur due to high sensitivity and thus the leakage protector trips, devices are 

powered off, and services are interrupted. 

 

To guarantee personal safety, the rated leakage action current of each leakage protector in the system must be equal 

to or less than 30mA (human body safety current is 30mA). When twice of the total leakage current of the system is 

greater than 30mA, the system must be equipped with two or more leakage protectors. 

 

For the leakage current value of each power supply model, see the power supply model parameter table in Chapter 

1. 

2.1.4  Static Discharge Damage Prevention 

To prevent damage from static electricity, pay attention to the following: 

 

Indoor dust prevention. 

 

Proper humidity conditions. 

2.2 Installation Site Requirements 

To ensure the normal working and a prolonged durable life of the equipment, the installation site must meet the following 

requirements. 

2.2.1  Ventilation 

Maintain a minimum clearance of 100 mm (3.94 in.) around the device. After various cables have been connected, they 

should be arranged into bundles or placed on the cabling rack to avoid blocking the air inlets. It is recommended to clean 

the switch at regular intervals (like once every 3 months). Especially, avoid dust from blocking the screen mesh on the 

back of the cabinet. 

2.2.2  Temperature and Humidity 

To  ensure  the  normal  operation  and  prolong  the  service  life  of  5/8-port  plastic  series  switch,  you  should  keep  proper 

temperature and humidity in the equipment room. 

If the equipment room has temperature and humidity that do not meet the requirements for a long time, the equipment may 

be damaged. 

 

In an environment with high relative humidity, the insulating material may have bad insulation or even leak electricity. 

Sometimes the materials may suffer from mechanical performance change and metallic parts may get rusted. 

Summary of Contents for RG-ES05































Reviews: