RTS TBX - TriBus ADAM User Instructions Download | Manualshive

Page: 26 / 48

background image

22

13.

Click

Finish

.

The Intercom Configuration window reappears

.

14.

Under Number of Ports in, make any

changes to the frames

for port allocation, as needed.

15.

Click

Test

to verify the configuration validity.

16.

Click

Apply

to apply the configuration to the intercom system.

The Intercom Configuration window closes and the configuration is applied to the intercom system.

«
...
24
25
26
27
28
...
»

Summary of Contents for TBX - TriBus ADAM

















































Reviews:

No comments

Related manuals for TBX - TriBus ADAM

BB-HGW700A - Network Camera Router

Brand: Panasonic Pages: 10

Brand: IBM Pages: 32

Brand: ZyXEL Communications Pages: 299

Brand: ZyXEL Communications Pages: 5

Brand: WAGO Pages: 2

DataPlot CB1224

Brand: B-G Instruments Pages: 4

Brand: Dahua Pages: 113

Brand: Rosco Pages: 20

Brand: ADTRAN Pages: 161

Brand: Paradyne Pages: 46

Brand: Hama Pages: 45

Brand: H3C Pages: 46

Brand: GRASS VALLEY Pages: 22

Zum ZUMMESH-NETBRIDGE

Brand: Crestron Pages: 2

Brand: Icom Pages: 7

Brand: Asus Pages: 221

WL-500W SuperSpeed N

Brand: Asus Pages: 123

Brand: Asus Pages: 151

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands