background image

28 

 

8.  DC input mains power to the enclosure and mains power must be filtered by a DC mains filters with 

attenuation characteristics of Corcom 6EH1 series filters or with similar filters with equal or greater 
attenuation characteristics.   

9.  Insulation strip length of 0.26 inches (6.5 mm) is required on all field wirings to the I/O card 

termination modules. 

10.  The disposal of any electronic products must be in accordance with local regulations (e.g. Directive 

2002/96/EC of the European Parliament and of the Council on waste electrical and electronic 
equipment).  Some RTP Corporation products contain materials that may be detrimental to the 
environment.  These materials may include, but are not limited to lead (in solder) and lithium (in 
batteries). 

11.  Prior to storage or shipping, the equipment must be packaged in accordance with the following 

guidelines: 

●  Inventory all items and inspect all components for damage. 
●  Verify that all fasteners are properly tightened and that the chassis I/O module retaining bar is 

properly installed. 

●  Wrap the chassis assembly in plastic bubble wrap. 
●  Select a suitable shipping box that provides at least 1½ inches of space between the equipment 

and all sides of the box.  This space shall be tightly packed with packing peanuts or bubble wrap 
to protect the equipment during storage or shipping. 

●  Close and secure the box with suitable packing tape. 
●  Do not stack boxes more than three high.  Store the boxes in a protected, dry environment.  Do 

not expose the boxes to rain or environmental conditions beyond the ranges specified for the 
equipment in this document. 

 

 

Summary of Contents for 3000 TAS































Reviews: