background image

 
 

 

14 

5  

Malfunctions and remedies compressor  

 
Malfunction 

Possible cause 

Remedy 

Oil pressure below  0.3 bar 
at operating temperature 

Drive speed to low  

Check drive speed 

Oil filter soiled 

Clean oil strainer 

Oil level to low  

Top up oil 

Oil pressure varies  

Oil level to low  

Top up oil 

Oil intake pipe leaking 

Check screw ed connection 

Oil foams 

Wrong oil grade 

Top up w ith approved oil 
grade  

Water in the oil 

Change oil 

Oil level to high 

Reduce oil 

Oil leakages 

Screw ed connection is 
leaking 

Check screw ed connection 

Compressed air pressure to 
high 

Drive speed to high 

Adjust drive speed 

Defective non return valve 

Replace non return valve 

Safety valve does not blow  
off 

Check safety valve 

Negative pressure gauge 
reading 65 mbar 

Suction filter clogged 

Clean/replace filter 
elements 

Speed to high 

Adjust drive speed  

 
 

Malfunctions and remedies motor  

 
Malfunction 

Possible cause 

Remedy 

Motor does not start  

No pow er supply 

Check fuses, connections 
and the pow er cable 

Phase monitoring 

Set main sw itch to position 
“ 2”  

Motor runs at half pow er 

Phase missing 

Check fuses 

Motor does not sw itch to 
phase 2 

Start delta connection 
defective 

Have repair w ork 
conducted by an expert 
only 

 
 

For immediate shut -

dow n in case of an emergency/a malfunction, press the “ emergency 

off”  button on the compressor unit. 

 

Summary of Contents for SiloKing 1100 LS















Reviews: