rtd BDM-610000049 User Manual Download Page 33

Page: 33 / 120

BDM-610000049

Rev G

Chapter 3: Connecting the cpuModule

Chapter 3

Connecting the cpuModule

This chapter provides information on all CMX158886 cpuModule connectors.

Proper Grounding Techniques

—page 24

Connector Locations

— page 24

Auxiliary Power (CN3)

—page 26

Utility Port Connector (CN5)

— page 28

SVGA Video Connector (CN18)

—page 31

LVDS Flat Panel Video Connector (CN19)

—page 33

EIDE Connector (CN10)

—page 34

ATA/IDE Disk Chip Socket (U16)

—page 35

Serial Port 1 (CN7) and Serial Port 2 (CN8)

— page 37

multiPort™ (CN6)

—page 42

USB 2.0 Connector (CN17)

— page 45

Ethernet (10/100Base-T and -TX) Connector (CN20)

—page 47

Audio (CN11)

—page 48

PC/104-Plus PCI Bus (CN16)

—page 49

Bridge Link (CN4)

—page 52

External Power Management (CN12)

—page 53

Optional RTC Battery Input (CN13)

—page 53

Fan Power, +5 V (CN14)

— page 53

Fan Power, Switched (CN15)

— page 54

Summary of Contents for BDM-610000049

























































































































Search results

Summary of Contents for BDM-610000049

Reviews:

Related manuals for BDM-610000049

Brands by name

Popular brands

rtd BDM-610000049, User Manual

Search results

Summary of Contents for BDM-610000049

Reviews:

Related manuals for BDM-610000049

Brands by name

Popular brands