RTA Techni Mobili RTA-3992D Assembly Instructions Manual Download Page 8

AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING 

CARE AND MAINTENANCE WARNINGS:

Do not exceed the indicated weight limits.

Do not expose the surfaces to direct sunlight or to extreme environmental conditions.

Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry

with a clean towel.

Do not use solvents or abrasive materials to clean the unit.

If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the

tabletop.

Do not seat on the unit or lean against it.

Do not allow small children to play under or over the unit.

The unit must be handled by at least 2 persons when moving in the same or adjacent rooms.

Before moving the unit, make sure to secure or remove any object that is heavy or might fall off.

When lifting the unit, use both hands and bend your knees, not your backs.

When transporting the unit to places far away, protect and secure the unit to avoid damage in transit.

Shall any part of the unit become defective during the warranty period, replacement parts might be

available to you at no charge. Please refer to the WARRANTY card included with the product.

The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for

damages or consequences due to accidents, incorrect assembly, negligence, improper use, modifications,

or not heeding the above warnings.

The warranty is limited to the continental United States. If you reside in Hawaii, Puerto Rico, U.S.

Dependencies or other countries, please contact the supplier from where the unit was purchased.

P.

8

RTA-

3992D

P.

8

3.3

 Lbs. (

1.5

 Kg)

3.3

 Lbs. (

1.5

 Kg)

WEIGHT LIMITS

110

 Lbs. (

50

 Kg)

3.3

 Lbs. (1

.5

 Kg)

3.3

 Lbs. (

1.5

 Kg)

3.3

 Lbs. (

1.5

 Kg)

44

 Lbs. (

20

 Kg)

Summary of Contents for Techni Mobili RTA-3992D









Reviews: