RTA 460ECBC-NNA1 Product User Manual Download

Page: 53 / 66

Real Time Automation, Inc.

1-800-249-1612

Device Status

- This will only display when viewing

All Adapters

Connected and Running

–

The gateway is connected to all the EtherNet/IP adapters that are enabled

and configured.

Connected and Idle

–

The gateway is connected to all the EtherNet/IP adapters that are enabled and

configured but the configured outputs are not yet valid.

Error: Timeout

–

One or more enabled EtherNet/IP adapters have timeouts.

Fatal Error: No Configuration

–

No EtherNet/IP adapter devices are configured or devices that are

configured are not enabled.

Unknown: First Scan Not Complete

–

I/O Parameters have been configured for an EtherNet/IP

adapter, but a connection has not been established yet.

Dependency Protocol Faulted

–

The dependent protocol is missing causing the communication to go

inactive.

LED Status

- This is the Status for

All Adapters

or the specific Adapter selected.

Solid Green (Connected)

–

The gateway is connected to all the EtherNet/IP adapters that are

configured and enabled.

Solid Green (Connected(Idle))

–

The gateway is connected to all the EtherNet/IP adapters that are

configured and enabled, but the configured outputs are not yet valid.

Flashing Green (Not Connected/First Time Scan)

–

The gateway has never been connected to an

EtherNet/IP adapter that is configured and enabled.
a)

Make sure there are no error codes being returned.

Make sure the adapter device is configured and online.

Flashing Red (Empty Scan List)

–

No EtherNet/IP adapters are configured/enabled.

Flashing Red (Connection Timeout) - One or more enabled EtherNet/IP adapters are timed out or
missing.
a)

Verify that the IP address of each EtherNet/IP adapter is valid and is on the same network as the
gateway.

Verify EtherNet/IP settings and ensure that the

Enable

checkbox is checked for the appropriate

device(s).

Verify the Instance numbers are valid for each EtherNet/IP adapter.

Flashing Red (Dependency Error) - The dependent protocol is missing or has errors causing the
communication to go inactive.
a)

The other protocol must be

Connected

Off

–

No Ethernet cable plugged in.

Summary of Contents for 460ECBC-NNA1



































































Search results

Summary of Contents for 460ECBC-NNA1

Reviews:

Related manuals for 460ECBC-NNA1

Brands by name

Popular brands

RTA 460ECBC-NNA1, Product User Manual

Search results

Summary of Contents for 460ECBC-NNA1

Reviews:

Related manuals for 460ECBC-NNA1

Brands by name

Popular brands