background image

 

Real Time Automation, Inc. 

34 

1-800-249-1612 

 

 

 

 

 

5)

 

Status_XY 

a)

 

There are two Statuses provided, one for each protocol. This gives access to the overall status of 
that Protocol. Each Bit has its own meaning as follows: 

 

 

 

Common Status:    0x000000FF (bit 0-7)1

st

 byte 

 
Hex:  Bit Position:   Decimal:     Explanation:  
 
0x00       0   

 

     

if we are a Slave/Server

 

0x01       0   

 

     

if we are a Master/Client

 

0x02       1   

      2          

connected (0 not connected)

 

0x04       2    

 

4          

first time scan

 

0x08       3    

 

     

idle (usually added to connected)

 

0x10       4            16         

running (usually added to connected)

 

0x20       5    

 

32 

    

 bit not used

 

0x40       6            64         

recoverable fault

 

0x80       7            128        

nonrecoverable fault

 

 

For this example, the ETC Status is mapped to a PLC tag called PLC_Status 

 

Example:

 ETC Status is 0x00000013 (19 decimal), here is the break down 

Hex 

      Bit      Decimal 

 

Explanation 

0x01 

    0(on)         1   

if we are a Master/Client

 

0x02 

    1(on)         2   

connected (0 not connected)

 

0x10 

    4(on)         16   

running (usually added to connected)

 

         

 

Total:        0x13          19   

 

 

External Faults:  

 

0x0000FF00 (bit 8-15)2

nd

 byte 

 

Hex:  Bit Position:   Decimal:     Explanation:  

 

0x00      8  

 

 

local control

 

0x01      8  

 

256 

 

remotely idle

 

0x02      9  

 

512 

 

remotely faulted

 

0x04      10  

 

1,024  

idle due to dependency

 

0x08      11  

 

2,048  

faulted due to dependency

 

 

Recoverable Faults:   0x00FF0000 (bit 16-23)3

rd

 byte 

 

Hex:  Bit Position:   Decimal:     Explanation:  

 

0x01      

16 

 

65,536 

recoverable fault - timed out

 

0x02      

17 

 

131,072 

recoverable fault - Slave err

 

 

Summary of Contents for 460ECBC-NNA1



































































Reviews: