RSL CG24 Monitor Owner'S Manual Download Page 46 | Manualshive

Page: 46 / 48

background image

44

TROUBLESHOOTING — Continued

RSL SPEEDWOOFER

Please read our captivating “More Than You Want to Know about Bass Man-

agement” section. It describes how to avoid abuse and distortion, and how to get the
best performance from your Speedwoofer.

No Sound from Your RSL Speedwoofer

tm

/ Subwoofer

Power indicator not lit

1. Check to confirm that your subwoofer is set to the “on” or “standby” position
and that the master power switch is “on”

2. Inspect the power cord. Make sure it is securely plugged in to the wall outlet
and subwoofer and that it has not been damaged.

3. Be sure the wall outlet is active.

4. Make sure the RSL Speedwoofer’s

tm

control box is attached and that the

shielded Category 5 Ethernet cable is properly attached (it will click into place).

5. Your RSL Speedwoofer amplifier contains a removable fuse designed to pro-
tect it from overheating, short circuits, and other potentially damaging occur-
rences. This fuse should be checked and is located in the power cord socket on
the amplifier.

Make sure the Speedwoofer

tm

amplifier is unplugged when accessing the

fuse.

A.You will need to insert a flat-head screwdriver (or appropriate object) in the
horizontal slot located on the power cord socket, just below where the cord
plugs in. This is the piece that contains the fuse.

B. Gently pry the fuse housing open until it detaches. Do not try to completely
remove the fuse housing. Extract the housing from the power cord socket,
remove the fuse and inspect it. If the wire inside the cylinder is severed or
displays a gap; the fuse is bad and needs to be replaced.

C. A spare fuse is provided and can be found in the small compartment in the
fuse housing. When replacing the fuse, always use a fuse of the same value.

D. If the new fuse blows, the amplifier requires service.

6. The RSL Speedwoofer

tm

10 has an internal circuit protection that could be

tripped. If you suspect this, turn down the subwoofer’s volume and turn off the
power. Wait 5 minutes before turning it on again.

«
...
44
45
46
47
48
»

Summary of Contents for CG24 Monitor

















































Reviews:

No comments

Related manuals for CG24 Monitor

Brand: Make Audio Pages: 8

Brand: Panasonic Pages: 132

Brand: Panasonic Pages: 10

Brand: AARU ENGINEERS Pages: 4

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 22

Brand: Panasonic Pages: 44

Sound Slayer SC-HTB01

Brand: Panasonic Pages: 12

Sound Slayer SC-HTB01

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands