background image

 

 

 

Declarations of compliance 

United States 

This equipment has been tested and found to comply with the limits for a Class 
A digital device, pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference when 
the equipment is operated in a commercial environment. This equipment 
generates, uses, and can radiate radio frequency energy and, if not installed 
and used in accordance with the instruction manual, may cause harmful 
interference to radio communications. Operation of this equipment in a 
residential area is likely to cause harmful interference in which case the user 
will be required to correct the interference at his own expense. 

Canada 

This digital apparatus does not exceed the Class A limits for radio noise 
emissions from digital apparatus set out in the Radio Interference Regulations 
of the Canadian Department of Communications. 

Le présent appareil numérique n

émet pas de bruits radioélectriques 

dépassant les limites applicables aux appareils numériques de la Classe A 
prescrites dans le Règlement sur le brouillage radioélectrique edicté par le 
ministère des Communications du Canada. 

EMC compliance 

The following warning may be applicable to your machine. 

WARNING

: This is a class A product. In a domestic environment this product 

may cause radio interference in which case the user may be required to take 
adequate measures.

Summary of Contents for ES-1000H














Reviews: