background image

12 

 

MBE ECU 

1)

 

Connect a laptop to the car and load Easimap. (This displays the engine 
sensor readings) 

2)

 

To achieve a base setting the throttle needs to be fully closed. To ensure it 
is, wind the idle adjuster screw out while watching the TPS reading 
displayed in Easimap. The value should reduce as you wind the screw out. 
Once the value stops reducing, the throttle is fully closed.

 

 
 
 
 
 
 
 
 

 
 

3)

 

Set the TPS value to 0.13. To do this, loosen the TPS using a 3mm allen key, 
as shown in the picture. Once loose, turn the TPS until its value shown on 
Easimap is 0.13, and re-tighten the securing screws 

 
 
 

 

 
 
 

 

4)

 

Using a 3mm allen key turn the idle screw up until the TPS value is 0.19 to 
0.20. 

5)

 

Now you are ready to start the engine. Check the engines oil, water and 
electrical connections. (Especially if it is a new engine installation). Once 
you have confirmed these are OK, start the engine and let it idle. Make 
sure the engine temperature is maintained within its operating 
parameters. Do not allow the water temperature to rise above 90°C. 

 

6)

 

Place the syncrometer in throttle body number 3. This body is not 
adjustable it is your base which the rest of the bodies need to match. The 
syncrometer will normally read between 5 and 7. 

 
 
 
 
 
 

 

 
 

7)

 

Place the syncrometer in the other bodies, using a 7mm spanner and 2mm 
allen key (as shown in the picture below) adjust the other bodies to match 
the reading from body number 3. Please note that turning the adjuster 
clockwise opens the body. To adjust, loosen the 7mm nut and turn the 
adjuster in the centre. Once the reading is correct, lock off the adjuster by 
tightening the 7mm nut and holding onto the 2mm allen key to stop it 
from moving. When balancing match the reading on cylinder 3 and 4 with 
the adjuster, then match 1 and 2 finally use the centre adjuster to match 
both sides

 
 
 
 
 
 
 
 
 

8)

 

Once all four bodies give the same reading on the syncrometer, the bodies 
are balanced. Give the engine a couple of small blips and check the TPS 
value returns to 0.19 to 0.20 and all the throttle bodies read the same on 
the syncrometer. 

TPS Adjuster Screws 

Idle adjuster 
screw 

TPS 

0.19 

Summary of Contents for GSX-R 1300 Turbo




















Reviews: