CX511 Paper Shredder / Pencil Sharpener / Letter Opener
Cautions:
1. Never allow children to shred or play with paper shredder or else serious
injury could occur.
2. Do not place hands or fingers into the shredder throat as serious injury
could result.
3. Never spray canned air or any type of spray lubricant into the shredder while
shredder is plugged in or serious injury could result.
4. Never place any lubricants or cleaning solutions into the paper shredder or
else serious injury could result.
5. Keep all loose articles of clothing, ties, jewelry, hair or other small items
away from the feed opening to prevent injury.
6. Remove all paper clips and staples from paper before shredding. The
shredder will cut staples and small paper clips; however, proper discretion
is recommended.
7. Keep the shredder turned off or unplugged when not in use for prolonged
periods of time.
8. When manually changing feed direction, pause long enough for the motor
to stop to avoid possible damage to the motor.
9. Always turn off and unplug the shredder prior to moving, cleaning or emptying
the wastebasket.
10.Empty the wastebasket frequently to avoid possible paper jams caused by
shredded material being pulled back into the cutter assembly.
Setup:
1. Place the Pencil Shavings Retention Cup provided with your shredder, inside
the metal ring attached to the inside of the wire mesh basket.
2. Place the shredder head securely on top of the wastebasket. Make sure that
the shredder head sits flush on top of the wastebasket or else the shredder
sharpener and opener will not work.
3. Plug the power cord into any standard 115 volt AC outlet.
4. Place the Power Slide Switch in the
AUTO
position.
Operating the shredder:
The model CX511 Power Slide Switch is located on the top of the shredder. The main
switch has three (3) settings:
1. When
AUTO
is selected, the shredding process is started automatically by
inserting the folded paper into the feed opening. The shredder will stop
automatically when the paper has completed its travel through the feed
opening.
2.
OFF
is used to terminate the AC power to the shredder. This mode is
recommended when the shredder is not being used for a prolong period of time.
When the switch is in the
OFF
position, the Shredder, Sharpener and
Opener will not work.
3.
REV
is used to assist in the removal of a paper jam, which reverses the
shredding process prior to a completed cycle, thus clearing the cutters.
Shredder capacity:
The CX511 will shred up to five (5) folded sheets of 20 lb. bond paper and will accept
paper widths up to 5". When shredding small material like credit card or receipts, insert
them through the middle of the feed opening.
Paper jams and motor overload situations:
The CX511 is equipped with a motor overload protection device. The normal short duty
cycle for continuous shredding at maximum capacity is 2 minutes on and 4 minutes off.
The power may terminate automatically in case of the following abnormal situations:
2
CX511 Paper Shredder / Pencil Sharpener / Letter Opener
1. Operating the shredder at the maximum 5 folded sheet capacity continuously for
a prolonged period of time, eg. more than 2 minutes without stopping.
2. Exceeding the shredding capacity, eg. inserting more than three (5) sheets of 20
lbs. paper at one pass, or if the paper is not fed squarely into the feed opening.
Both abnormal operations may result in the activation of the thermal motor overload
protection which terminates the power to the shredder. A major paper jam could cause
the thermal motor overload protection to terminate AC power to the motor. Never allow
the shredder to remain in a jammed condition with the AC power turned on. If this occurs
you should:
In case of a major paper:
1. Set the power switch to the
OFF
position or unplug the power cord from the AC
outlet and wait at least 15 minutes for the thermal overload protection to reset.
2. Grasp the excess paper from the top and pull it out as you place the power switch
in the
REV
position. Be careful not to place your fingers near the feed opening
or else serious harm could result.
3. Set the power switch back to the
AUTO
position.
4. You are now ready to resume normal shredding.
*** NOTE*** The Paper Shredder, Pencil Sharpener, and Letter Opener
are independent units. NEVER use more than one of them at a time to
avoid excessive ware to the motor
.
Pencil Sharpener
1. To prevent motor damage, remove the pencil from the pencil opening when point
is sharpened.
2. Refrain from inserting hard materials such as pens, chalk, crayons or coloring
pencils which will damage or clog the cutting blades. Maximum pencil diameter
should not exceed 7.4mm. Standard #2 type pencil recommended.
To use the Sharpener:
1. With the switch in the
AUTO
position, insert the pencil into the pencil opening. The
sharpening starts immediately.
2. Pull out pencil at the end of the sharpening cycle.
3. Be sure to empty the pencil shavings retention cup frequently.
To use the Letter Opener:
1. Be sure that the letter inside the envelope is not against the leading edge of the
envelope will be inserted into the opener.
2. With the switch in the
AUTO
position, place the leading edge of the envelope into
the opening of the Letter Opener. The cutters will start and feed the envelope
through automatically.
Specifications:
Shred Type:
Cross-Cut
Shred Width:
4 x 35mm
Shredding Capacity:
5 Folded Sheets
Feed Opening:
5"
Dimension:
10"(H) x 9.25”(W) x 6.8”(D)"
Weight:
6 lbs.
Input:
120 volt AC, 2.0 amp.
3
Summary of Contents for CX511
Page 2: ......
