11
2 Operation
GB
2
Operation
2.1 Before use
1.
Unpack the appliance and all its accessories.
2.
Check the contents for completeness and possible damages. Scope of delivery see
Z
Fig. 1.
3.
Insert the end of the suction hose into the intake opening (Fig. 2) of the cylinder vacuum cleaner until you
hear and feel it locking into place. Make sure that the release catch is on the upper side.
4.
Insert the handle into the upper end of the telescopic tube (Fig. 3/A).
5.
Attach the floor nozzle to the bottom end of the telescopic tube (Fig. 3/B).
6.
Adjust the length of the telescopic tube. Press down the release latch on the tube (Fig. 3/C) to do this. Then
extend the telescopic tube to the desired length. Let go of the release catch while pulling until it locks in
place. You will hear a distinct click.
7.
Attach the supplied accessory nozzles to the accessory holder (Fig. 3/C1). If you put the furniture brush
(Fig. 1/4) onto to the crevice nozzle (Fig. 1/3), the twin holders can take 3 accessory nozzles. The
upholstery nozzle (Fig. 1/5) may then be attached to the remaining holder.
2.2 Vacuum cleaning
1.
Push the desired nozzle onto the lower end of the telescopic tube or the handle (Fig. 4).
2.
If using the floor nozzle, set the "carpet/hard floor" selector according to the type of floor to be cleaned
(Fig. 5):
- "Carpet" position (Fig. 5/A): for deep- and short-pile carpets, runners
- "Hard floor" position (Fig. 5/B): for smooth floors, e.g. laminate, tiles, PVC, etc.
3.
Pull out the power cord by the plug up to the yellow mark (Fig. 6/1).
4.
Insert the mains plug into a socket with ground/safety contact.
5.
Switch on the vacuum cleaner by pushing the on/off switch with integrated power control (Fig. 6/4).
6.
Adjust the suction power to suit the floor by turning the on/off switch with integrated power control (Fig. 6/4).
- By turning the control clockwise, suction power is increased, e.g. for removing deep-set dirt particles from
carpets, runners, crevices, etc.
- By turning it counter-clockwise, suction power is reduced, e.g. for cleaning drapes, etc.
ATTENTION:
Always transport or ship the appliance in its original packaging to avoid damage. Keep the packaging for
such an event.
Dispose of no longer needed packaging material properly.
NOTE:
Immediately contact your dealer if you have found damage resulting from transport.
2
B
C
A
1
3
WARNING:
Danger of injury! A damaged appliance must never be used. Check the cylinder vacuum cleaner and the
power cord each time before using the appliance.
WARNING:
Danger of injury! Especially when vacuum-cleaning stairs make sure that you always stand on a higher level
than the appliance.
ATTENTION:
Only use the cylinder vacuum cleaner with all filters intact, in dry condition and correctly fitted. Make sure
that no openings are clogged.
ATTENTION:
Before vacuuming, make sure that the fitted nozzle and the set suction power suit the surface to be cleaned.
Also observe the flooring manufacturer's recommendations.
WARNING:
Danger of electric shock! If the red mark (Fig. 6/2) is showing retract the cable back to the yellow mark
(Fig. 6/1) using the carrying-handle with its integrated cable retraction button (Fig. 6/3). Otherwise, the
power cord may be damaged.
NOTE:
With the bypass vent (Fig. 7/1) you can quickly reduce suction power if less power is needed, e.g.to release
curtains accidentally sucked in.
4
5
3
1
2
4
6
1
7
M2700.book Seite 11 Freitag, 19. März 2010 8:54 08
