![background image](http://html.mh-extra.com/html/royal/45-013-40/45-013-40_original-operating-instructions_1493959021.webp)
4. Technical data
Engine displacement
37.2 cm
3
Maximum engine capacity
1.3 kW
Bar length
32 cm
Cutter rail length
14” (35 cm)
Chain pitch
(3/8”), 10 mm
Chain thickness
(0.05”), 1.27 mm
Idling speed
3400 rpm
Maximum speed with cutting equipment
11000 rpm
Tank capacity
330 ml
Oil tank capacity
230 ml
Anti-vibration function
Yes
Chain wheel teeth
6 x 9.525 mm
Chain brake
Yes
Clutch Yes
Automatic chain lubrication
Yes
Low-kickback chain
Yes
Net weight without chain and chain bar
4.9 kg
Net weight (dry)
6,1 kg
Fuel consumption (specific)
560 g / kWh
L
pA
sound pressure level
100 dB(A)
K
pA
uncertainty
1.5 dB(A)
L
WA
sound power level
112 dB(A)
K
WA
uncertainty
1.5 dB(A)
Vibration a
hv
(front handle)
max. 4.85 m/s
2
K
hv
uncertainty 1.5
m/s
2
Vibration a
hv
(rear handle)
max. 6.18 m/s
2
K
hv
uncertainty 1.5
m/s
2
Chain type
OREGON 91VG053X (91P053X)
Bar type
OREGON 140SCEA041 (140SDEA041)
Spark plug
L8RTF
5. Before starting the equipment
Important:
Do not start the engine until the saw
is fully assembled.
Important:
Wear protective gloves at all times
when handling the chain.
5.1 Fit the chain bar
To ensure that the bar and the chain are supplied
with oil, USE ONLY THE ORIGINAL BAR. The oiling
hole (Fig. 2/Item A) must be kept clear of dirt and any
build-up of residue.
1.
Make sure the Chain brake lever is pulled back
into the DISENGAGED position (Fig. 3A)
2.
Remove the two bar fastening nuts (B). Remove
the cover (Fig. 3B).
3.
Using a screwdriver, run the adjustment screw
(D) COUNTERCLOCKWISE until the TANG (E)
(projecting prong) is to the end of its travel toward
the clutch drum and sprocket (Fig. 3B/3C).
4.
Fit the open end of the chain bar over the die bar
pins (F) (Fig. 3C/3D).
5.2 To install saw chain
1.
Spread chain out in a loop with cutting edges (A)
pointing CLOCKWISE around loop (Fig. 4A).
2.
Slip the chain around the sprocket (B) behind the
clutch (C). Make sure the links fit between the
sprocket teeth (Fig. 4B).
3.
Guide the drive links into the groove (D) and
around the end of the bar (Fig. 4B).
NOTE:
The saw chain may droop slightly on the lower
part of bar. This is normal.
4.
Pull the chain bar forward until the chain is closely
seated. Make sure that all the drive links are in
the groove of the bar.
5.
Fit the clutch cover and fasten it with 2 screws.
Make sure that the pivot (Fig. 3C/Item E) fits into
the chain bar (Fig. 3D/Item G). The chain must
not slip off the bar when you do this. Tighten the
two nuts by hand and then follow the instructions
for adjusting the tension in ADJUSTING THE
CHAIN TENSION.
21
GB
Anleitung_RPC_3835_SPK7:_ 25.08.2010 13:24 Uhr Seite 21