background image

2

TABLE OF CONTENTS

TOPIC PAGE

1. Introduction ........................................................................................................   3 
2. Safety Precautions ..............................................................................................  4
3. Product Identification ..........................................................................................  4
4. Included with Laminator ......................................................................................  5 
5. Loading Film ......................................................................................................... 6
6.  Threading Film 

6.1. Hot Film ..................................................................................................... 7-8   

6.2. Cold Film ......................................................................................................  9 

6.3. Mounting ....................................................................................................  10

7. Control of Roller Pressure ................................................................................  11
8. Control Panel ....................................................................................................  12
9.  Laminating Steps 

9.1. Hot Laminating ...................................................................................... 13-14 

9.2. Cold Laminating .........................................................................................  15

10. Using Cross Cutter ..........................................................................................  16
11. Using Slitter (Only for the model with slitter) ................................................... 17
12. Maintenance ...................................................................................................  18
13. Troubleshooting ..............................................................................................  19
14. Recommended Temperature and Speed Settings .........................................  20
15. Specifications ..................................................................................................  21
16. Warranty ..........................................................................................................  22

Summary of Contents for RSL-1062CR























Reviews: