background image

MODEL                                RSC-1650H                          RSC-1650HR                          RSC-1650C

Power Supply  

220-240V       120V                 220-240V              200V          220-240V     120V

50/60HZ

50/60HZ

50/60HZ

50HZ

50/60HZ

50/60HZ

single phase

RSC  Series

4

3

3.  INSTALLATION

Note: The laminator should be installed by a trained service technician.

ELECTRICAL REQUIREMENTS

The laminator comes fully assembled, except for the feed table, paper guide, and heat
assembly (RSC-1650H and RSC-1650HR) to avoid shipping damage. Upon arrival,
thoroughly inspect the unit. It is imperative that any shipping damage is reported and a
claim is filed with the delivering carrier immediately upon receipt.

The laminator should be located in an area with adequate work space for feeding graphics
and lamination materials.

Avoid placing the laminator in a dusty area or near sources of extreme heat or cold.

Once the laminator is in place, lock the casters into position(“ON” position).  Always unlock
the casters (“OFF”  position) when moving to a different location.       

4.  INCLUDED WITH LAMINATOR

Thoroughly inspect the parts and the unit.  It is imperative that any missing parts are
reported and a claim is filed with the reseller immediately upon receipt of shipment. 

Royal Sovereign recommends that a licensed electrician ensuresproper power installation
to your laminator in accordance with electrical codes in your area.

The laminator should have a dedicated power line.  

230V UL

120V UL

220V EU

240V UK

Part Name

Laminator

Owner's Manual

Heating Element Installation Instruction

(RSC-1650H and RSC-1650HR)

Registration Card

2"(57mm) / 3´´ (76mm) Core Plugs

Core - Bolts

Dust Cover

Spare Motor Fuse - FUSE(50T)

(6.3A)

Spare Main Power Fuse - FUSE(65TS)

(15A) 

8 - Round head 5/16´´ (9mm) screw.

8 - Allen/Hex head 3/16´´ (5mm)

(Included with option only)

Front Feeder and Rear Rewinder Kit

(Included with option only)

1

1

1

1

6/4

10

1

1

1

10/10

2/2

Quantity

Picture

12 - 3/16"screw  (M5

@?hf

/Xe@??W.?h

V/X?@?W.Y?h

?V/?@?.Yhe

W.?/X?he

?W.Y?V/Xhe

?.Y?eV/he

10mm).

12 - Spring Washer(

?@h

J5h

?O&Hh

O2@@@@@?O@g

W2@0M??W@@@@g

?W&(M?e?7<I'@g

?7@Hf?@eN@g

J@5?fJ5e?@g

7@H?f7Hhe

@@g@?he

@@f?J5?he

@@f?7H?he

@@f?@hf

3@L?eJ5hf

N@1?e7Hhf

?3@Le@?fW.g

?V')KC5?e?O.Yg

V4@@Y??O20Y?g

?@@@@0M?h

J(M?hf

7Hhg

@?hg

5.1)

(Included with option only)

12/12

220V AU

Summary of Contents for RSC Series











Reviews: