background image

19

RSC-1650H/HR and RSC-1650C Laminators

OWNER'S MANUAL

Royal Sovereign International Inc.

17.  WARRANTY

Royal Sovereign International warrants the equipment sold is free from defects in
material and workmanship for a period of One (1) year for Parts and Labor from the date
of installation, excluding lamination rollers which are warranted for Six (6) months. This
warranty is extended only to the original purchaser.  This warranty is the only warranty
made by Royal Sovereign International and cannot be modified or amended.  Royal
Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy
under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such
defective part or product. These remedies are only available if Royal Sovereign’s
examination of the product discloses to Royal Sovereign’s satisfaction that such defects
actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized
alternation or modification, incorrect line voltage, fire, accident, flood or other hazard.

The warranty made herein is in lieu of all other warranties, expressed or implied,
including any warranty or merchantability or fitness for a particular purpose. Royal
Sovereign will not be liable for personal damage or personal injury (unless primarily
caused by its negligence), loss of profit, or other incidental or consequential damages
arising out of the use or inability to use this equipment.      

This warranty specifically does not cover damage to laminating rollers caused by
knives, razor blades, or any sharp objects or abrasives, or failure caused by adhesives,
or damage caused by lifting, tilting and/or any attempt to position the machine other
than rolling on the installed  castors or feet on even surfaces, or improper use of the
machine. Warranty repair or replacement by Royal Sovereign or its authorized
Reseller(s) does not extend the warranty beyond the initial one year period from the
date of installation. Unauthorized customer alterations will void this warranty.         

LIMITED WARRANTY

www.royalsovereign.com

Read all instructions carefully before use.

For any Customer Support needs please choose the 

Customer Support tab

on www.royalsovereign.com  

RS Holland B.V.

Columbusstraat 25 - 3165 AC Rotterdam, 
The Netherlands
E-mail : [email protected]

[email protected]

RS International Australia PTY. LTD.

30 Prime Drive, Seven Hills, NSW 2147, Australia
TEL  : +61) 2-9674-2127     
FAX  : +61) 2-9674-2027
E-mail : [email protected]

CORPORATE HEADQUARTERS

Royal Sovereign International Inc.

2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.
TEL : +1 ) 800-397-1025        FAX : +1 ) 201-750-1022
E-mail : [email protected]

Royal Sovereign Inc. 

<Oversea Sales Office>

1001, World Meridian II, 426-5, Gasan-dong, 
Geumcheon-gu, Seoul, 153-759, KOREA
TEL  : +82)2-2025-8800     FAX  : +82)2-2025-8830
E-mail : [email protected]

RS Canada Inc.

164 Oakdale Road, Toronto, Ontario M3N 2S5
CANADA
TEL : +1

)

416-741-8400     FAX : +1

)

416-741-8185 

E-mail : [email protected]

Summary of Contents for RSC Series











Reviews: