background image

 

Safety precautions 

1.  Installation, testing, repair or replacement of this product must be done by professional or person sent by dealer. 

2.  Power supply facilities connected to this product must meet national standards, and all power supply parameters must tally 

with this product (See electric parameters chart). Forbid lengthen the power cable. 

3.  This  product  must  be  powered  by  a  RCD  with  residual  current  not  exceeding  30mA.  Besides,  for  power  supply  of  this 

product,  an  all-pole  disconnection  power  switch  meeting  requirements  must  be  installed.  And  regularly  confirm  that  all  these 

devices are effective. 

4.  The  equipotential  (the  yellow  and  green  wire)  connector  of  this  product  must  be  permanently  connected  with  external 

equipotential connector. 

5.  During installation and application, forbid cutting any of the connecting wires of the product. Do not disassemble the electric 

cabinet and control panel. Otherwise, our company will not take any responsibility for product failure, leakage or  electric shock 

resulted. 

6.  Acetone, ammonia water, gasoline and such organic solvent and strong acidic chemicals will dissolve and corrode different 

parts of this product, so please avoid contacting such substances during installation and application. 

7.  The product installation area must be well ventilated, dry and without corrosive gassy. If not used for a long time, please cut 

off power supply. 

8.  Before  connecting  cold  and  hot  water  pipes,  please  discharge  the  water  that  has  been  staying  inside  the  pipes,  so  as  to 

prevent damaging water control equipment. 

9.  Children using this product must be accompanied by an adult. The old and patient should use this product carefully. 

Cleaning and maintenance 
 

1.  For  daily  cleaning  of  the  massage  bathtub,  please  use  common  liquid  detergent  and  soft  cloth,  but  do  not  use  detergent 

containing ketone or ammonia water; do not use disinfectant containing formaldehyde for disinfection. 

2.  Surface stains can be cleaned by rubbing with toothpaste and soft cloth. 

3.  For slight surface scratches or cigarette burns, please burnish with 2000# levigation sandpaper and then do polishing. 

4.  For stains on electroplated parts, please wipe slightly with soft lint. Do not use coarse cloth or solvents like thinner. 

5.  Often clean water suction device to prevent blocking. 

6.  Irregularly check for inconvenience in use caused by pipe crack or folding. 

7.  Often check electrical wire, switches, plugs for fall-off or damage, so as to repair in-time. 

8.  To lengthen service life of the product, please note that continuous use should not exceed 3 hours. 

 
Basic technical parameters 

 

1.  Supply voltage: AC190V--240V 50-60Hz 

9.  Electromagnetic valve: AC12V 8W 

2.  Water pump power: AC220V 750W 

10.  Music power: <15W 

3.  Air pump power: AC220V 750W 

11.  Frequency range: FM88--108MHz 

4.  Heater power: AC220V 1500W 

12.  S/N radio: >45dB 

5.  Dielectric strength: 1500V 1Min 

13.  Water proof scale: IPX4 

6.  Electricity leakage:<0.25mA 

 

 

7.  Ozone: AC 12W 8W 

 

 

8.  Water lamp voltage: AC12V 20W 

 

 

Summary of Contents for B313












Reviews: