background image

2014 GM 1500 Pickup Front 2.5” Kit 

 
                                   Thank you for choosing Rough Country for all your suspension needs. 

 

Rough  Country  recommends  a  certified  technician  install  this  system.  In  addition  to  these  instructions,  professional 
knowledge of disassemble/reassembly procedures as well as post installation checks must be known.  Attempts to install 
this system without this knowledge and expertise may jeopardize the integrity and/or operating safety of the vehicle.

 

 

Please read instructions before beginning installation. Check the kit hardware against the parts list on this page.  Be sure 
you  have  all  needed  parts  and  know  where  they  go.    Also  please  review  tools  needed  list  and  make  sure  you  have 
needed tools.

 

PRODUCT USE INFORMATION 

 

 

As a general rule, the taller a vehicle is, the easier it will roll. Seat belts and shoulder harnesses should be worn at all 
times. Avoid situations where a side rollover may occur.   

 

Generally, braking performance and capability are decreased when larger/heavier tires and wheels are used. Take this 
into consideration while driving. Do not add, alter, or fabricate any factory or after-market parts to increase vehicle height 
over the intended height of the Rough Country product purchased. Mixing component brands is not recommended. 

 

Rough  Country  makes  no  claims  regarding  lifting  devices  and  excludes  any  and  all  implied  claims. We  will  not  be  re-
sponsible for any product that is altered. 

 

This suspension system was developed using a 285/70/17, tire with factory wheels. 

Note 

if wider tires are used, offset 

wheels will be required and trimming will be required. 
 

**Note**

 The electric power steering must be unplugged before any of the steering components are removed. Failure to 

do so may cause damage to the electric power steering. 

 

If you have any questions concerning the design, function, and correct use of our products please contact us at 800-222-
7023.

 

NOTICE TO DEALER AND VEHICLE OWNER 

 

Any vehicle equipped with any Rough Country product should have a “Warning to Driver” decal installed on the inside of 
the windshield or on the vehicle’s dash.  The decal should act as a constant reminder for whoever is operating the vehi-
cle of its unique handling characteristics.  

  

INSTALLING DEALER  - it is your responsibility to install the warning decal and forward these installation instructions on 
to the vehicle owner for review.  These instructions should be kept in the vehicle for its service life. 

92130300 

Summary of Contents for 92130300

















Reviews: