Section 5 Operating Instructions
SG7MTS Manual
www.rottlermfg.com
5-13
MANUAL
Buttons
BACK - goes 1 page back.
VERTICAL ZERO - tap the SET button to set the vertical spindle height.
VERTICAL POSITION - height spindle is at from VERTICAL ZERO height set.
SPINDLE RPM REVERSE – runs spindle Counter Clockwise
FORWARD – runs spindle Clockwise
Tap display and enter desired RPM
FINISH RPM – same as above, you can instantly change RPSMs to the programed setting buy tapping
the forward or reverse button. You can instantly change from forward to reverse if needed.
ANGLE - this is the actual angle the angle sensor is in.
ZERO - buy taping this button you can ZERO the angle reading for easier setup.
LAMP - turns ON and OFF the LED work lights
CENTER PILOT – locks and unlocks the spindle sphere
WORKHEAD FLOAT - floats the workhead
Operation Tips before Machining Valve Seats
Clean valve guide with a brush to remove foreign matter.
Required spindle rotation speed will vary, depending on seat hardness. As seat hardness increases, so
does the spindle speed will change. Some will require full speed
NOTE: If valve guides are so badly worn that the proper centering will be impossible, it will be
necessary to replace that valve guide to achieve the a concentric valve seat.
See following suggested machining speed chart .
Summary of Contents for SG7MTS
