
Section 2 Installation
SG7 Manual
www.rottlermfg.com
2-9
Air Supply
It is very important the air source for the SG7 machine be
moisture free. Water and oil in the line will result in early cylinder
and valve failure. The factory recommends installing a water trap
at the machine.
Attach a 100 PSI air source to the appropriate intake in the
small enclosure located on the left rear of the machine near the
bottom.
Bellow you will set the Air regulator panel for the different
settings on the flouting planes on the machine.
And cabinet cooler air regulator.
Air Adjustments
Float
The float regulator is located at the rear of the spindle base on the bottom of the interconnect box.
If the machine is not floating properly, it could be from too much or too little air from the regulator. Turn
the regulator all the way off (full counter clockwise). Start turning the regulator slowly clockwise while
continually checking the Work Head for proper floatation. Once the correct float is established, lock the
regulator into place by pushing in on the blue adjusting knob.
Use as little air as possible to achieve correct floatation. Using too much air will could
cause the spindle base to move slightly to the right when going into tilt. This will cause
a scratch up the side of the cylinder.
Summary of Contents for SG7
