Roto-Mix 425 Operator'S Manual Download Page 28

Page: 28 / 92

TROUBLESHOOTING

ALWAYS DISCONNECT AND LOCKOUT ELECTRICAL POWER (STATIONARY MODELS) OR DISENGAGE POWER

TAKE OFF AND REMOVE KEYS FROM TRACTOR OR TRUCK BEFORE CLEANING, ADJUSTING, LUBRICATING

OR SERVICING THIS MACHINE. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.

NOTE:

CHART NOT ALL INCLUSIVE OF PROBLEMS. CONTACT DEALERSHIP FOR ASSISTANCE.

Page 28

PROBLEM

POSSIBLE CAUSE

POSSIBLE REMEDY

Excessive Shearing Of Powershaft

Shear Pin

High Speed Engagement Of PTO Or

Conveyor.

Decrease RPM Of The Engine Bef-

ore Engaging PTO Or Lowering Dis-

charge Chute On Trailer Mixers.

Wrong Shear Pin.

See Page 19.

High Moisture, Thin Stemmed Mate-

rials And/or Not Fine Enough

Chopped Length.

Decrease The Size Of Load Being

Mixed And/or Use Materials

Chopped To 1-1/2" Or Less Length.

Conveyor Plugging Before The Door

Is Opened.

The Conveyor Must Be Running.

Vibration Or Growling In Rear Struc-

ture

Drive Sprockets Out Of Lline

Check And Realign

Universal Joints Out Of Alignment.

Check And Realign

Worn Out Bearing.

Replace Bearing.

Chains Jumping Sprocket Teeth

Idler Spings Loose.

Adjust Idlers As Instructed On Page

24.

Drive Sprockets Out Of Line

Check And Realign

Worn Sprocket Teeth.

Replace Sprocket.

Drive Chains Breaking

Sprocket Misalignment

Align Sprockets

Usually Causes Side Bar Breakage

Due To Chain Riding Up On

Sprocket Teeth.

See Possible Remedies To “chains

Jumping Sprocket Teeth” Above

Excessive Bearing Failure

Improper Lubrication

Refer To Lubrication Chart.

Contamination

Check Seal

Excessive Loads.

Refer To General Information About

Machine Loading

Summary of Contents for 425





























































































Search results

Summary of Contents for 425

Reviews:

Related manuals for 425

Brands by name

Popular brands

Roto-Mix 425, Operator'S Manual

Search results

Summary of Contents for 425

Reviews:

Related manuals for 425

Brands by name

Popular brands