background image

 

 

Equipment Operation 

Follow the guidelines below to ensure safe operation of the unit: 
1. NEVER access dangerous chemicals or other materials to prevent possible hazard of explosion 

and damage. 

2. Do not operate the unit without lids or covers to prevent possible hazards. 
3. A temporary conductivity caused by condensation might occur even though this series is rated 
Pollution Degree 2 in accordance with IEC 664. 
 
 

Symbols  

The following symbols are used on the power supplies: 
 

 

 
 

 

Indicates an area where a potential shock hazard may exist. 
Consult  the  manual  to  avoid  possible  personal  injury  or 
instrument damage. 
 
 
 
Indicates disposal instruction. 

DO NOT

 throw this unit into a municipal trash bin when this unit 

has  reached  the  end  of  its  lifetime. To  ensure  utmost  protection 
of the global environment and minimize pollution, please recycle 
this unit. 
 
 
Caution/  Warning: Indicates  a  hazardous  situation  which,  if  not 
avoided, could result in death or serious injury. 

Max. voltage: 500 V 
Max. current: 400 mA 
Max. watt: 120 W 
 
 

 
 
Encountering Problems 

 

Check the troubleshooting section. 

 

Call Technical Service under 0049 721 5606-0 

If the unit must be shipped back for repair, contact Carl Roth GmbH + Co. KG for shipping 
instructions. The unit will be repaired or replaced as quickly as possible and returned to you. 
 
Contact: Phone 0049 721 5606-0;   Fax 0049 721 5606-149;   

[email protected]

 

 

All Roth products available for delivery have undergone rigorous quality controls. 

 
 
PACKING LIST 

No. Items

 

Description

 

Power Supply 

Power Cord 

Instruction Manual 

 

Summary of Contents for MINI









Reviews: